2RM/24VAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: 2 Relay Module
2SRM/24VAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: 2 Single Relay Module
2VID/24VAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: 2 Voltage to Current Driver
3RM/24VAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: 3 Relay Module
43191679-001
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories
Single feedback potentiometer 220/135 ohm operating range, for 20 mm models
43191679-002
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories
Single feedback potentiometer 220/135 ohm operating range, for 38 mm models
43191679-007
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories
Single feedback potentiometer 10 kohm operating range, for 20 mm models
43191679-008
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories
Single feedback potentiometer 10 kohm operating range, for 38 mm models
43191679-011
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Accessories
Feedback potentiometer 10 kohm, operating range
43191679-012
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Accessories
Feedback potentiometer 220 ohm operating range
43191680-002
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories
Dual end switches SPDT, adjustable (250 V~, 10 A)
43191680-005
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Accessories
Dual end switches SPDT, adjustable (250 V~, 10 A)
43191680-205
Trend Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425
Accessories
Auxiliary switch (250 V~, 10 A)
43196000-001
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
High temperature kits for:
V5011R/S, V5013R/E; V5328A/V5329A DN15..32
43196000-002
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
High temperature kits for:
V5016A/V5025A/V5050A DN15..80; V5049A DN15..65; V5095A DN20..80; V5328A/V5329A DN40..80
43196000-038
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
High temperature kits for:
V5015A/V5016A/V5025A/V5049A/V5050A/B/V5328A 38 mm
4DIX/24VAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Input Modules
Product description: 4 Digital Input Expander
5112-11/U
Trend Two way characterized control ball valves, PN25, DN15-50, VBG2
Linkage set for Damper actuators
Linkage set for VBG valves; DN15-32 for usage with S03.. actuators; DN15-50 for usage with N05.., S05.. actuators
5112-19/U
Trend Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves
Replacement stem assembly for VBG valve, DN15, DN20
5112-20/U
Trend Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves
Replacement stem assembly for VBG valve, DN25, DN32
5112-21/U
Trend Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN40, DN50 valves
Replacement stem assembly for VBG valve, DN40, DN50
5112-51/U
Trend Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN40, DN50 valves
Linkage set for VBG valves DN40, DN50 to M6061, M7061
5585100
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
Accessories
Spare adjustment cap (pack of 10)
6RM/24VAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: 6 Relay Module
963L/CD
Trend 963 Supervisor
The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display. 963 now contains all the secure features of the previous secure version (963 Secure. It assists with compliance to FDA regulation 21 CFR Part 11 and has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 provides maximum protection for the data it stores, and the system it is controlling. and imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others. All 963 secure features are now licensed as part of the standard product.
Comments: stand alone
963L/UP/963S/3USER
Trend 963 Supervisor
Upgrades
Upgrade from 963L to 963S
963S/CD/10USER
Trend 963 Supervisor
The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display. 963 now contains all the secure features of the previous secure version (963 Secure. It assists with compliance to FDA regulation 21 CFR Part 11 and has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 provides maximum protection for the data it stores, and the system it is controlling. and imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others. All 963 secure features are now licensed as part of the standard product.
Comments: web server 3 user
963S/CD/25USER
Trend 963 Supervisor
The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display. 963 now contains all the secure features of the previous secure version (963 Secure. It assists with compliance to FDA regulation 21 CFR Part 11 and has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 provides maximum protection for the data it stores, and the system it is controlling. and imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others. All 963 secure features are now licensed as part of the standard product.
Comments: web server 3 user
963S/CD/3USER
Trend 963 Supervisor
The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display. 963 now contains all the secure features of the previous secure version (963 Secure. It assists with compliance to FDA regulation 21 CFR Part 11 and has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 provides maximum protection for the data it stores, and the system it is controlling. and imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others. All 963 secure features are now licensed as part of the standard product.
Comments: web server 3 user
963S/SMS/CD/10USER
Trend 963 SMS
963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.
Model: SMS
Comments: web server 3 user
963S/SMS/CD/25USER
Trend 963 SMS
963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.
Model: SMS
Comments: web server 3 user
963S/SMS/CD/3USER
Trend 963 SMS
963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.
Model: SMS
Comments: web server 3 user
963S/SMS/UP/*/10USER
Trend 963 SMS
Upgrades
Upgrade from 963/SMS/any user to 10 users
963S/SMS/UP/*/25USER
Trend 963 SMS
Upgrades
Upgrade from 963/SMS/any user to 25 users
963S/UP/*/10USER
Trend 963 Supervisor
Upgrades
Additional Client licences any user to 10 user
963S/UP/*/25USER
Trend 963 Supervisor
Upgrades
Additional Client licences any user to 25 user
963S/UP/963S/SMS/10USER
Trend 963 SMS
Upgrades
Upgrade from 963S 10 User to 963S/SMS 10 User
963S/UP/963S/SMS/25USER
Trend 963 SMS
Upgrades
Upgrade from 963S 25 User to 963S/SMS 25 User
963S/UP/963S/SMS/3USER
Trend 963 SMS
Upgrades
Upgrade from 963S 3 User to 963S/SMS 3 User
AC-15FS
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
Accessories
Soldering fitting for DN15 valve, pipe size 12 mm
AC-15FT
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
Accessories
External threaded fitting for DN15 valve, pipe size 3/8"
AC-15TF
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
Accessories
Internal threaded fitting for DN15 valve pipe size Rp 1/2"
AC-15TF-1
Trend Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves
Internal threaded fitting for VBG DN15 valve, pipe size Rp 1/2"
AC-20FS
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
Accessories
Soldering fitting for DN20 valve, pipe size 15 mm
AC-20FT
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
Accessories
External threaded fitting for DN20 valve, pipe size 1/2"
AC-20TF
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
Accessories
Internal threaded fitting for DN20 valve pipe size Rp 3/4"
AC-25T
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories
External threaded fitting for DN25 valve, pipe size R1"
AC-25TF
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories
Internal threaded fitting for DN25 valve, pipe size Rp1"
AC-32T
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories
External threaded fitting for DN32 valve, pipe size R11/4"
AC-32TF
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories
Internal threaded fitting for DN32 valve, pipe size Rp11/4"
AC-40T
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories
External threaded fitting for DN40 valve, pipe size R11/2"
AC-40TF
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories
Internal threaded fitting for DN40 valve, pipe size Rp11/2"
AC-50TF
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
Accessories
Internal threaded fitting for DN50 valve pipe size Rp 2"
ACC/24VAC
Trend IQView4 Local Touch Screen Display
Accessories
230/24 Vac, 24 VA, transformer for IQView4, with surface mounting lugs, and through earth (ground) connection
ACC/DF
Trend Plant Temperature Sensors (NTC10k)
Accessories
Duct flange for the TB/TI
ACC/FS
Trend Plant Temperature Sensors (NTC10k)
Accessories
Mounting kit for the T/TFR-4
ACC/Flange/12mm/5
Trend Plant Humidity Sensors
Accessories
Pack of 5 clamps for HT Duct
ACC/HTD/FILTER
Trend Plant Humidity Sensors
Accessories
Pack of 5 filters for HT Duct
ACC/HTO/FILTER
Trend Plant Humidity Sensors
Accessories
Pack of 5 filters for HT Outside
ACC/SP
Trend Pressure, Current sensor, Liquid
Accessories
Steam Pigtail for use with steam or water above 85 oC
ACC/UF
Trend Plant Temperature Sensors (NTC10k)
Accessories
Universal Fixing Clip (retrofit to existing pockets)
ACCA-WC-L
Trend Splash proof covers
Model: Large cover for ML64, ML74, 1800N actuators
ACCA-WC-M
Trend Splash proof covers
Model: Medium size cover for ML64, ML74, 600N actuators
ACCA-WC-S
Trend Splash proof covers
Model: Small cover for ML64, ML74, 400N actuators
ACCW/CONFIGKIT
Trend Wireless Receiver
Accessories
Programming kit for XW/R/IQ including connection cable between receiver, PC, and supply, and CD containing configuration software
ACCW/FK/SS
Trend Wireless Receiver
Accessories
Stainless steel wall bracket for mounting XW/R/IQ at a distance of 28 cm from wall
ACCW/RW/IQ
Trend Wireless Receiver
Accessories
Wireless sensors repeater
ACN-15T
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
Accessories
External threaded fitting for DN15 valve, pipe size 3/8"
ACN-20T
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
Accessories
External threaded fitting for DN20 valve, pipe size 1/2"
AQ/D
Trend Air quality sensor
For detection of unpleasant odours, tobacco smoke, and vapours emitted by such materials as furniture, carpets, paint, glue, etc.
Protection class: AQ/D IP67 Housing
Output signal: 0..10Vdc
Pre-calibrated for ease of commissioning
On site calibration if required with status LED
Long term reliability
Power supply: 24Vacdc
Mounting place: air duct
Housing (HxWxD): no
Housing (dia x D): 85mm|55mm
Immersion depth: 200mm
AQ/S
Trend Air quality sensor
For detection of unpleasant odours, tobacco smoke, and vapours emitted by such materials as furniture, carpets, paint, glue, etc.
Protection class: AQ/D IP67 Housing
Output signal: 0..10Vdc
Pre-calibrated for ease of commissioning
On site calibration if required with status LED
Long term reliability
Power supply: 24Vacdc
Mounting place: internal wall
Housing (HxWxD): 86mm|86mm|35mm
Housing (dia x D): no
Immersion depth: no
AS2
Trend Actuator for V5421B1090
Optional accessories
End switch
ATU2040A
Trend Rotary Actuator
Mounting kit for non-Honeywell valves
Universal kit for almost all valves
AV-D-10
Trend Air velocity sensor
Media: Air, 0 to 10m/s (default); selectable by link for 0 to 15m/s or 0 to 20m/s
Response time: 4s (default) or 1s selectable by link
Mounting place: air duct
Protection class: IP 65 Housing
Humidity 5..95 %rh, non-condensing
Output signal: 2..10Vdc + 4..20mA
Mounting: in duct
AV-R-10
Trend Air velocity sensor
Media: Air, 0 to 10m/s (default); selectable by link for 0 to 15m/s or 0 to 20m/s
Response time: 4s (default) or 1s selectable by link
Mounting place: air duct
Protection class: IP 65 Housing
Humidity 5..95 %rh, non-condensing
Output signal: 2..10Vdc + 4..20mA
Mounting: remote
CABLE-CONTROL
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Control Spares
Product description: Set of linking cable for HVAC400 older than March 2018
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
CABLE/EJ100057A
Trend Leads
Product description: IQ1xx Supervisor lead, 5 way SIL F to 9 way D F (2m length)
CABLE/EJ101442
Trend Leads
Product description: Adapter lead from supervisor to IQ25x (9 way female to RJ11)
CABLE/EJ105650
Trend Leads
Product description: RJ11 plug to RJ11 plug with crossover to connect to IQ3, IQ2xx, and some IQ1xx controllers local supervisor ports
CO2/T/D
Trend CO2/T/ Temperature, Humidity Sensors
A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)
Mounting place: air duct
Display: no
Housing (HxWxD): 105mm|97mm|57mm
Immersion depth: no
CO2/T/H/Disp/S
Trend CO2/T/ Temperature, Humidity Sensors
A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)
Mounting place: internal wall
Display: 4 Digit LCD
Housing (HxWxD): 86mm|86mm|26mm
Immersion depth: 260mm
CO2/T/H/S
Trend CO2/T/ Temperature, Humidity Sensors
A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)
Mounting place: internal wall
Display: no
Housing (HxWxD): 86mm|86mm|26mm
Immersion depth: 260mm
CO2/T/S
Trend CO2/T/ Temperature, Humidity Sensors
A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)
Mounting place: internal wall
Display: no
Housing (HxWxD): 86mm|86mm|26mm
Immersion depth: 260mm
COMP-IP21-KIT1
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit for SmartDrive HVAC232/402, size MI1
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
COMP-IP21-KIT2
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit for SmartDrive HVAC232/402, size MI2
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
COMP-IP21-KIT3
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit for SmartDrive HVAC232/402, size MI3
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
COMP-LOADER
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive PC connection tools and cables
Product description: SmartDrive Compact Parameter download/upload and PC interface tool with cable for USB connection to PC
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
COMP-LOADER-NC
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive PC connection tools and cables
Product description: SmartDrive Compact Parameter download/upload and PC interface tool without cable
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
COMP-NEMA1-KIT1
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit with additional wiring terminal cover for SmartDrive HVAC232/402, size MI1
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
COMP-NEMA1-KIT2
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit with additional wiring terminal cover for SmartDrive HVAC232/402, size MI2
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
COMP-NEMA1-KIT3
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit with additional wiring terminal cover for SmartDrive HVAC232/402, size MI3
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
CONTROL-BOARD1
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Control Spares
Product description: Control box and boards for HVAC400 drives
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
DCPSU-24-1.3
Trend IQView4 Local Touch Screen Display
Accessories
24Vdc Power Supply Input 100-240V Ourput 24Vdc 1.3A
DPCM/24VAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: Dual Phase Cut Module; 15 VA max per channel.
DPIL/0.5
Trend Differential Pressure, Current sensor, Liquid
The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA
Pressure range: 0...0.5bar
Max. pressure: 3bar
DPIL/1
Trend Differential Pressure, Current sensor, Liquid
The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA
Pressure range: 0...1bar
Max. pressure: 5bar
DPIL/10
Trend Differential Pressure, Current sensor, Liquid
The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA
Pressure range: 0...10bar
Max. pressure: 20/12.bar
DPIL/2.5
Trend Differential Pressure, Current sensor, Liquid
The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA
Pressure range: 0...2.5bar
Max. pressure: 12bar
DPIL/4
Trend Differential Pressure, Current sensor, Liquid
The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA
Pressure range: 0...4bar
Max. pressure: 12bar
DPIL/6
Trend Differential Pressure, Current sensor, Liquid
The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA
Pressure range: 0...6bar
Max. pressure: 12bar
DPS1000
Trend Differential pressure switch for air (DPS)
Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa
Pressure adjustment range: 200...1000Pa
Switching differential: 1mbar
DPS1000/BOX25
Trend Differential pressure switch for air (DPS), packs of 25
Multi pack versions of filter monitors or flow switches for air, non-combustible, non aggressive gases in air conditioning and ventilating installations. For all specification details see single pack version page
Product description: Box with 25 pieces DPS1000
DPS200
Trend Differential pressure switch for air (DPS)
Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa
Pressure adjustment range: 20...200Pa
Switching differential: 0.1mbar
DPS200/BOX25
Trend Differential pressure switch for air (DPS), packs of 25
Multi pack versions of filter monitors or flow switches for air, non-combustible, non aggressive gases in air conditioning and ventilating installations. For all specification details see single pack version page
Product description: Box with 25 pieces DPS200
DPS2500
Trend Differential pressure switch for air (DPS)
Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa
Pressure adjustment range: 500...2500Pa
Switching differential: 1.5mbar
DPS400
Trend Differential pressure switch for air (DPS)
Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa
Pressure adjustment range: 40...400Pa
Switching differential: 0.2mbar
DPS400/BOX25
Trend Differential pressure switch for air (DPS), packs of 25
Multi pack versions of filter monitors or flow switches for air, non-combustible, non aggressive gases in air conditioning and ventilating installations. For all specification details see single pack version page
Product description: Box with 25 pieces DPS400
DPS500
Trend Differential pressure switch for air (DPS)
Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa
Pressure adjustment range: 50...500Pa
Switching differential: 0.2mbar
DPSK
Trend Differential pressure transmitter for air (DPTE)
Accessories
Duct Kit, including 2m silicone-hose and 2 joining pipes DPSJ with screws
DPSL
Trend Differential pressure transmitter for air (DPTE)
Accessories
Mounting brackets L-shaped
DPSL/H
Trend Differential Pressure, Switch, Liquid
Differential pressure, vacuum and overpressure switch for monitoring neutral and slightly aggressive liquids and gases. It can be used as a flow switch fitted across an orifice plate.
Kind of pressure: differential pressure, relative
Pressure connection: G1/8" (DIN 259); 1/8" BSP female thread
Electrical connection: screw terminals
Protection class: IP54
Housing material: Case: Brass, Cover: Plastic, Diaphragm: EPDM
Media temp.: -10...80C
Medium: liquid/gaseous
Ambient temperature: -10...80C
Max. pressure: 10bar
Pressure range: 150...1000mbar
DPSL/L
Trend Differential Pressure, Switch, Liquid
Differential pressure, vacuum and overpressure switch for monitoring neutral and slightly aggressive liquids and gases. It can be used as a flow switch fitted across an orifice plate.
Kind of pressure: differential pressure, relative
Pressure connection: G1/8" (DIN 259); 1/8" BSP female thread
Electrical connection: screw terminals
Protection class: IP54
Housing material: Case: Brass, Cover: Plastic, Diaphragm: EPDM
Media temp.: -10...80C
Medium: liquid/gaseous
Ambient temperature: -10...80C
Max. pressure: 10bar
Pressure range: 40...200mbar
DPTE100
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...100/250Pa
Max. pressure: 20kPa
DPTE1000
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...1000/2500Pa
Max. pressure: 40kPa
DPTE1000S
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -1000...1000Pa
Max. pressure: 20kPa
DPTE1002
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...1000/2500Pa
Max. pressure: 40kPa
DPTE100S
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -100...100Pa
Max. pressure: 20kPa
DPTE102
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...100/250Pa
Max. pressure: 20kPa
DPTE102S
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: -100...100Pa
Max. pressure: 20kPa
DPTE250
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...250/500Pa
Max. pressure: 20kPa
DPTE252
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...250/500Pa
Max. pressure: 20kPa
DPTE500
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...500/1000Pa
Max. pressure: 20kPa
DPTE5000
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...5000/10000Pa
Max. pressure: 60kPa
DPTE5002
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...5000/10000Pa
Max. pressure: 60kPa
DPTE500S
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -500...500Pa
Max. pressure: 20kPa
DPTE502
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...500/1000Pa
Max. pressure: 20kPa
DPTE50S
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -50...50Pa
Max. pressure: 20kPa
DPTE52S
Trend Differential pressure transmitter for air (DPTE)
Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet
2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: -50...50Pa
Max. pressure: 20kPa
DR100GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 100mm
Kvs value: 160
Max. delta P: 100kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 30Nm
Port connection: flanges DIN2531
DR125GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 125mm
Kvs value: 250
Max. delta P: 70kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 30Nm
Port connection: flanges DIN2531
DR15-2GMLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Internal threads
DN size: 15mm
Kvs value: 2.5
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads
DR150GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 150mm
Kvs value: 630
Max. delta P: 50kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 40Nm
Port connection: flanges DIN2531
DR15GMLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Internal threads
DN size: 15mm
Kvs value: 4
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads
DR200GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 200mm
Kvs value: 1600
Max. delta P: 50kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 40Nm
Port connection: flanges DIN2531
DR200GFLA1
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 200mm
Kvs value: 1000
Max. delta P: 50kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 40Nm
Port connection: flanges DIN2531
DR20GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 20mm
Kvs value: 6.3
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531
DR20GMLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Internal threads
DN size: 20mm
Kvs value: 6.3
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads
DR25GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 25mm
Kvs value: 10
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531
DR25GMLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Internal threads
DN size: 25mm
Kvs value: 10
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads
DR32GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 32mm
Kvs value: 16
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531
DR32GMLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Internal threads
DN size: 32mm
Kvs value: 16
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads
DR40GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 40mm
Kvs value: 25
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531
DR40GMLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Internal threads
DN size: 40mm
Kvs value: 25
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads
DR50GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 50mm
Kvs value: 40
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531
DR65GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 65mm
Kvs value: 63
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531
DR80GFLA
Trend Three-way rotary valve PN6
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN6
Reduced delta P: 40kPa
Flanges
DN size: 80mm
Kvs value: 100
Max. delta P: 100kPa
Torque for max. delta P: 30Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531
DRA-02L
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Display panel kits
Product description: NXL door installation set for display panel, 2m cable
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
DRA-04B
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Display panel kits
Product description: NXS door installation set for display panel, 4m cable
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
DRA-04L
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Display panel kits
Product description: NXL door installation set for display panel, 4m cable
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
DRA02B
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Display panel kits
Product description: NXS door installation set for display panel, 2m cable
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
DRU25-10
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 25mm
Kvs value: 10
DRU25-16
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 25mm
Kvs value: 16
DRU25-2.5
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 25mm
Kvs value: 2.5
DRU25-4.0
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 25mm
Kvs value: 4
DRU25-6.3
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 25mm
Kvs value: 6.3
DRU32-10
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 32mm
Kvs value: 10
DRU32-16
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 32mm
Kvs value: 16
DRU32-25
Trend Three-way rotary valve PN10
For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Pressure rating: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Universal Rotary Valve
DN size: 32mm
Kvs value: 25
EDS-205
Trend IQ411 and IQ412 Controllers
Accessories
5 port U/M Ethernet Switch
EEM230-D-M
Trend Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication
Interface: M-Bus
Certificates: no
EEM230-D-M-MID
Trend Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication
Interface: M-Bus
Certificates: MID
EEM230-D-MO
Trend Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication
Interface: ModBus RTU
Certificates: no
EEM230-D-MO-MID
Trend Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication
Interface: ModBus RTU
Certificates: MID
EEM230-D-P
Trend Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication
Interface: pulse
Certificates: no
EEM230-D-P-MID
Trend Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication
Interface: pulse
Certificates: MID
EEM230-SEALCAP
Trend Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D
20 sealcaps (for 10 energy meters)
EEM400-D-M
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: M-Bus
Certificates: no
EEM400-D-M-MID
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: M-Bus
Certificates: MID
EEM400-D-MO
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: ModBus RTU
Certificates: no
EEM400-D-MO-MID
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: ModBus RTU
Certificates: MID
EEM400-D-P
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: pulse
Certificates: no
EEM400-D-P-MID
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: pulse
Certificates: MID
EEM400-SEALCAP
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
20 sealcaps (for 5 energy meters)
EEM400C-D-M
Trend Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: M-Bus
Certificates: no
EEM400C-D-M-MID
Trend Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: M-Bus
Certificates: MID
EEM400C-D-MO
Trend Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: ModBus RTU
Certificates: no
EEM400C-D-MO-MID
Trend Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: ModBus RTU
Certificates: MID
EEM400C-D-P
Trend Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: pulse
Certificates: no
EEM400C-D-P-MID
Trend Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D
Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication
Interface: pulse
Certificates: MID
ENC-Slot-MI1-MI3
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: Required external cover to fix option boards on HVAC232/402 frame size 1..3 for devices up to 5,5 kW
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
ENC-Slot-MI4-MI5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: Required internal moulding to fix option boards on HVAC232/402 frame size 4..5 for devices bigger than 5,5 kW
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
ENCLS-600002
Trend IQeco31 controller 24V version
Accessories
IQECO/IQL secondary terminal cover.
ENCLS/MBOX/XTEND
Trend Xtend24
Accessories
Metal enclosure (with integral DIN rail and transformer mounting).
EVA1-DANFOSS
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Adapters
Danfoss-RA adapter
FT6960-18
Trend Single-stage frost protection thermostat (FT69)
Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65
Temperature element: capillary with bulb
Capillary tube length: 1.8m
Mechanical lock/reset: manual
FT6960-30
Trend Single-stage frost protection thermostat (FT69)
Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65
Temperature element: capillary
Capillary tube length: 3m
Mechanical lock/reset: manual
FT6960-60
Trend Single-stage frost protection thermostat (FT69)
Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65
Temperature element: capillary
Capillary tube length: 6m
Mechanical lock/reset: manual
FT6961-18
Trend Single-stage frost protection thermostat (FT69)
Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65
Temperature element: capillary with bulb
Capillary tube length: 1.8m
Mechanical lock/reset: automatic
FT6961-30
Trend Single-stage frost protection thermostat (FT69)
Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65
Temperature element: capillary
Capillary tube length: 3m
Mechanical lock/reset: automatic
FT6961-60
Trend Single-stage frost protection thermostat (FT69)
Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65
Temperature element: capillary
Capillary tube length: 6m
Mechanical lock/reset: automatic
GVCPI-100
Trend Solenoid gas valve flanged, normally closed
CPI switches
CPI switch for the GVF100-230
GVCPI-20-25
Trend Solenoid gas valve screwed, normally closed
CPI switches
CPI switch for the GVS20-230 & GVS25-230
GVCPI-32-40
Trend Solenoid gas valve screwed, normally closed
CPI switches
CPI switch for the GVS32-230 & GVS40-230
GVCPI-50
Trend Solenoid gas valve screwed, normally closed
CPI switches
CPI switch for the GVS50-230
GVCPI-65F-80
Trend Solenoid gas valve flanged, normally closed
CPI switches
CPI switch for the GVF65-230 and GVF80-230
GVF100-230
Trend Solenoid gas valve flanged, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air.
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVF65-230 and GVF80-230 have adjustable maximum flow rate on the bottom of the coil
4 auxiliary pressure taps with Rp 1/4" threaded connections, 2 on the inlet side, 2 on the outlet side.
Max. operating pressure: 200mbar
Port connection: flanges ISO7005
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Flanged 220...240 Vac versions
Valve size: 4in.
Optional CPI-switch: GVCPI-100
GVF65-230
Trend Solenoid gas valve flanged, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air.
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVF65-230 and GVF80-230 have adjustable maximum flow rate on the bottom of the coil
4 auxiliary pressure taps with Rp 1/4" threaded connections, 2 on the inlet side, 2 on the outlet side.
Max. operating pressure: 200mbar
Port connection: flanges ISO7005
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Flanged 220...240 Vac versions
Valve size: 2 1/2in.
Optional CPI-switch: GVCPI-65F-80
GVF80-230
Trend Solenoid gas valve flanged, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air.
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVF65-230 and GVF80-230 have adjustable maximum flow rate on the bottom of the coil
4 auxiliary pressure taps with Rp 1/4" threaded connections, 2 on the inlet side, 2 on the outlet side.
Max. operating pressure: 200mbar
Port connection: flanges ISO7005
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Flanged 220...240 Vac versions
Valve size: 3in.
Optional CPI-switch: GVCPI-65F-80
GVS20-230
Trend Solenoid gas valve screwed, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Threaded 220...240 Vac versions
Valve size: 3/4in.
Optional CPI-switch: GVCPI-20-25
GVS25-230
Trend Solenoid gas valve screwed, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Threaded 220...240 Vac versions
Valve size: 1in.
Optional CPI-switch: GVCPI-20-25
GVS32-230
Trend Solenoid gas valve screwed, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Threaded 220...240 Vac versions
Valve size: 1 1/4in.
Optional CPI-switch: GVCPI-32-40
GVS40-230
Trend Solenoid gas valve screwed, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Threaded 220...240 Vac versions
Valve size: 1 1/2in.
Optional CPI-switch: GVCPI-32-40
GVS50-230
Trend Solenoid gas valve screwed, normally closed
Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s
Threaded 220...240 Vac versions
Valve size: 2in.
Optional CPI-switch: GVCPI-50
HON-NX8-KIT
Trend Trend Open Network Node (TONN8)
Spare Parts
TONN8 Accessory Kit WIFI-Antenna + RS485 and power terminals
HSS-DPS
Trend Dew-point switch
This early-warning dew-point switch is designed for use in monitoring cooling water pipes or chilled surfaces in order to determine if temperatures are approaching the dewpoint. It is suitable for mounting on flat and round surfaces. The switch measures the relative humidity prevailing directly at the chilled surface and can thus be used to:
regulating cooling performance
switching cooling systems ON and OFF
signalling if the temperature is approaching the dew-point
Status indication with LED, showing condensation danger
Switching point at 90 %rh, hysteresis 5 %rh
Ambient temperature: 0...50C
Protection class: IP40
Mounting: wall, duct or pipe (max. 50 mm)
Power supply: 24Vacdc
Switch function/capacity: potential free changeover contact; max. 24 Vac/dc, 1 A
Wiring connection: 5-pole push-in terminals, max. 1,5mm2
HT/D
Trend Plant Humidity Sensors
Duct and externally mounted relative humidity and temperature sensors for HVAC applications. The certified 2% high accuracy (duct only) and standard 3% versions offer excellent linearity and stability over a wide humidity range (10 to 90 %RH).
The Externally mounted sensor is fitted with a radiation shield to avoid solar, rain and wind effects.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
R.H. output signal: 4..20mA
Temperature range: 0...40C
Precalibrated for ease of commissioning
IP65
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
Adjustable depth duct mounting flange option (duct version)
Radiation shield reduces solar, rain, and wind effects (outside version)
R.H. calibration: 3%rh
Temperature element: NTC10k
Output signal: no
Mounting place: air duct
HT/D/2%
Trend Plant Humidity Sensors
Duct and externally mounted relative humidity and temperature sensors for HVAC applications. The certified 2% high accuracy (duct only) and standard 3% versions offer excellent linearity and stability over a wide humidity range (10 to 90 %RH).
The Externally mounted sensor is fitted with a radiation shield to avoid solar, rain and wind effects.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
R.H. output signal: 4..20mA
Temperature range: 0...40C
Precalibrated for ease of commissioning
IP65
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
Adjustable depth duct mounting flange option (duct version)
Radiation shield reduces solar, rain, and wind effects (outside version)
R.H. calibration: 2%rh
Temperature element: Pt1000
Output signal: 4..20mA
Mounting place: air duct
HT/O
Trend Plant Humidity Sensors
Duct and externally mounted relative humidity and temperature sensors for HVAC applications. The certified 2% high accuracy (duct only) and standard 3% versions offer excellent linearity and stability over a wide humidity range (10 to 90 %RH).
The Externally mounted sensor is fitted with a radiation shield to avoid solar, rain and wind effects.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
R.H. output signal: 4..20mA
Temperature range: 0...40C
Precalibrated for ease of commissioning
IP65
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
Adjustable depth duct mounting flange option (duct version)
Radiation shield reduces solar, rain, and wind effects (outside version)
R.H. calibration: 3%rh
Temperature element: NTC10k
Output signal: no
Mounting place: wall outside
HT/S
Trend Space Humidity Sensors
Wall mounted relative humidity measurement combined with temperature measurement. The certified 2% high accuracy and standard 3% versions offer excellent linearity and stability over a wide humidity range.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
Temperature range: 0...40C
Mounting place: internal wall
Precalibrated for ease of commissioning
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
R.H. calibration: 3%rh
Temperature element: NTC10k
Output signal: no
HT/S/2%
Trend Space Humidity Sensors
Wall mounted relative humidity measurement combined with temperature measurement. The certified 2% high accuracy and standard 3% versions offer excellent linearity and stability over a wide humidity range.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
Temperature range: 0...40C
Mounting place: internal wall
Precalibrated for ease of commissioning
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
R.H. calibration: 2%rh
Temperature element: Pt1000
Output signal: 4..20mA
HVAC-DOOR-KIT
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Display panel kits
Product description: SmartDrive HVAC door installation set for display panel, 3m cable
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-4
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 4 (HVAC400-1P1..HVAC400-5P5)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 5 (HVAC400-7P5..HVAC400-15P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-6
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 6 (HVAC400-18P..HVAC400-30P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-7
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 7 (HVAC400-37P..HVAC400-55P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-8
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 8 (HVAC400-75P..HVAC400-110P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-9
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 9 (HVAC400-132P..HVAC400-160P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-SUP-FR08
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC400 Cooling Fans
Product description: HVAC400, power supply, frame size 8, HVAC400-75Px - HVAC400-110x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-FAN-SUP-FR09
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC400 Cooling Fans
Product description: HVAC400, power supply, frame size 9, HVAC400-132x - HVAC400-160x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-HMI-A
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive HVAC display panels
Product description: SmartDrive HVAC advanced commissioning display/keypad with parameter copy function
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-IP54FAN-FR04
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 4, HVAC400-1P1x - HVAC400-5P5x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-IP54FAN-FR05
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 5, HVAC400-7P5x - HVAC400-15Px
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-IP54FAN-FR06
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 6, HVAC400-18Px - HVAC400-55Px
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-IP54FAN-FR08
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 8, HVAC400-75Px - HVAC400-110x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-IP54FAN-FR09
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 9, HVAC400-132x - HVAC400-160x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC-TERM-KIT
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Control Spares
Product description: Kit of terminal for HVAC400x drives
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
HVAC03C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 1.1kW
Low overload Icont: 3.3A
High overload (for Machines): 0.75kW
High overload Icont: 2.2A
HVAC04C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 1.5kW
Low overload Icont: 4.3A
High overload (for Machines): 1.1kW
High overload Icont: 3.3A
HVAC05C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 2.2kW
Low overload Icont: 5.6A
High overload (for Machines): 1.5kW
High overload Icont: 4.3A
HVAC07C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 3kW
Low overload Icont: 7.6A
High overload (for Machines): 2.2kW
High overload Icont: 5.6A
HVAC09C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 4kW
Low overload Icont: 9A
High overload (for Machines): 3kW
High overload Icont: 7.6A
HVAC12C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 5.5kW
Low overload Icont: 12A
High overload (for Machines): 4kW
High overload Icont: 9A
HVAC16C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 7.5kW
Low overload Icont: 16A
High overload (for Machines): 5.5kW
High overload Icont: 12A
HVAC232-1P1-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Low overload (for Fan/Pump): 1.1kW
Low overload Icont: 4.8A
Size: 2
HVAC232-1P5-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Low overload (for Fan/Pump): 1.5kW
Low overload Icont: 7A
Size: 2
HVAC232-2P2-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Low overload (for Fan/Pump): 2.2kW
Low overload Icont: 9.6A
Size: 3
HVAC232-P37-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Low overload (for Fan/Pump): 0.37kW
Low overload Icont: 2.4A
Size: 1
HVAC232-P55-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Low overload (for Fan/Pump): 0.55kW
Low overload Icont: 2.8A
Size: 1
HVAC232-P75-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Low overload (for Fan/Pump): 0.75kW
Low overload Icont: 3.7A
Size: 2
HVAC23C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 11kW
Low overload Icont: 23A
High overload (for Machines): 7.5kW
High overload Icont: 16A
HVAC31C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 15kW
Low overload Icont: 31A
High overload (for Machines): 11kW
High overload Icont: 23A
HVAC38C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 18.5kW
Low overload Icont: 38A
High overload (for Machines): 15kW
High overload Icont: 31A
HVAC400-110-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 110kW
Low overload Icont: 205A
Size: 8
HVAC400-110-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 110kW
Low overload Icont: 205A
Size: 8
HVAC400-11P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 11kW
Low overload Icont: 23A
Size: 5
HVAC400-11P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 11kW
Low overload Icont: 23A
Size: 5
HVAC400-132-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 132kW
Low overload Icont: 261A
Size: 9
HVAC400-132-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 132kW
Low overload Icont: 261A
Size: 9
HVAC400-15P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 15kW
Low overload Icont: 31A
Size: 5
HVAC400-15P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 15kW
Low overload Icont: 31A
Size: 5
HVAC400-160-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 160kW
Low overload Icont: 310A
Size: 9
HVAC400-160-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 160kW
Low overload Icont: 310A
Size: 9
HVAC400-18P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 18.5kW
Low overload Icont: 38A
Size: 6
HVAC400-18P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 18.5kW
Low overload Icont: 38A
Size: 6
HVAC400-1P1-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 1.1kW
Low overload Icont: 3.4A
Size: 4
HVAC400-1P1-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 1.1kW
Low overload Icont: 3.4A
Size: 4
HVAC400-1P5-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 1.5kW
Low overload Icont: 4.8A
Size: 4
HVAC400-1P5-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 1.5kW
Low overload Icont: 4.8A
Size: 4
HVAC400-22P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 22kW
Low overload Icont: 46A
Size: 6
HVAC400-22P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 22kW
Low overload Icont: 46A
Size: 6
HVAC400-2P2-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 2.2kW
Low overload Icont: 5.6A
Size: 4
HVAC400-2P2-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 2.2kW
Low overload Icont: 5.6A
Size: 4
HVAC400-30P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 30kW
Low overload Icont: 61A
Size: 6
HVAC400-30P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 30kW
Low overload Icont: 61A
Size: 6
HVAC400-37P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 37kW
Low overload Icont: 72A
Size: 7
HVAC400-37P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 37kW
Low overload Icont: 72A
Size: 7
HVAC400-3P0-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 3kW
Low overload Icont: 8A
Size: 4
HVAC400-3P0-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 3kW
Low overload Icont: 8A
Size: 4
HVAC400-45P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 45kW
Low overload Icont: 87A
Size: 7
HVAC400-45P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 45kW
Low overload Icont: 87A
Size: 7
HVAC400-4P0-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 4kW
Low overload Icont: 9.6A
Size: 4
HVAC400-4P0-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 4kW
Low overload Icont: 9.6A
Size: 4
HVAC400-55P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 55kW
Low overload Icont: 105A
Size: 7
HVAC400-55P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 55kW
Low overload Icont: 105A
Size: 7
HVAC400-5P5-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 5.5kW
Low overload Icont: 12A
Size: 4
HVAC400-5P5-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 5.5kW
Low overload Icont: 12A
Size: 4
HVAC400-75P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 75kW
Low overload Icont: 140A
Size: 8
HVAC400-75P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 75kW
Low overload Icont: 140A
Size: 8
HVAC400-7P5-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 7.5kW
Low overload Icont: 16A
Size: 5
HVAC400-7P5-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 7.5kW
Low overload Icont: 16A
Size: 5
HVAC400-90P-21A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP21
Protection class: IP21
Low overload (for Fan/Pump): 90kW
Low overload Icont: 170A
Size: 8
HVAC400-90P-54A
Trend Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC
Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
IP54
Protection class: IP54
Low overload (for Fan/Pump): 90kW
Low overload Icont: 170A
Size: 8
HVAC402-11P-21
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 11kW
Low overload Icont: 23A
Size: 4
HVAC402-15P-21
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 15kW
Low overload Icont: 31A
Size: 5
HVAC402-18P-21
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 18.5kW
Low overload Icont: 38A
Size: 5
HVAC402-1P1-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 1.1kW
Low overload Icont: 3.3A
Size: 2
HVAC402-1P5-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 1.5kW
Low overload Icont: 4.3A
Size: 2
HVAC402-2P2-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 2.2kW
Low overload Icont: 5.6A
Size: 2
HVAC402-3P0-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 3kW
Low overload Icont: 7.6A
Size: 3
HVAC402-4P0-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 4kW
Low overload Icont: 9A
Size: 3
HVAC402-5P5-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 5.5kW
Low overload Icont: 12A
Size: 3
HVAC402-7P5-21
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 7.5kW
Low overload Icont: 16A
Size: 4
HVAC402-FAN-FR4
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 Cooling Fans
Product description: HVAC402, main fan, size 4, HVAC402-7P5-21 - HVAC402-11P-21
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
HVAC402-FAN-FR5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
HVAC232/402 Cooling Fans
Product description: HVAC402, main fan, size 5, HVAC402-15P-21 - HVAC402-18P-21
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
HVAC402-P55-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 0.55kW
Low overload Icont: 1.9A
Size: 1
HVAC402-P75-20
Trend Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402
Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE
400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Low overload (for Fan/Pump): 0.75kW
Low overload Icont: 2.4A
Size: 1
HVAC46C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 22kW
Low overload Icont: 46A
High overload (for Machines): 18.5kW
High overload Icont: 38A
HVAC61C5
Trend Inverters 1,1..30kW, IP54, NXL HVAC
Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54
IP54
Low overload (for Fan/Pump): 30kW
Low overload Icont: 61A
High overload (for Machines): 22kW
High overload Icont: 46A
HVACDOORKIT
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Display panel kits
Product description: HVAC232/402 door installation set including 2m cable and display
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
IQ3XACT/XML/UP
Trend IQ3 Input/Output modules
Accessories
Upgrade to add XML services to IQ3xact v2.2 or greater
IQ3XCITE/128/LAN/24
Trend How to use this catalogue
Searching for products can be done in 4 different ways:
Use the TREE structure at the left. The tree also shows up in the middle, including some main pictures. The choosen options from the tree show up at the top. All texts and pictures are clickable.
Use the PRODUCT SEARCH box, for keying a Typenumber, or a text. The result list shows clickable options for catalogue pages, and downloadable Product Documentation Files.
Use the SITEMAP option at the top. The complete tree structure shows up, including some main pictures. All texts are clickable.
Use the TYPE option at the top. The complete list of all Product Typenumbers of the catalogue appears, in alpha-numerical order. Each Typenumber is clickable.
Pictures and Product Documentation Files are available for download, for example:
Click on the product picture on this page. A second browser opens. A low resolution colour JPG, or a high resolution black/white TIF can be downloaded (JPG: 150 pixels width, TIF: 3 cm width)
Click on the PDF symbol at the right of the part number at the bottom of this page. A second browser opens. Select the document that is needed.
IQ3XCITE/XML/UP
Trend IQ3 Input/Output modules
Accessories
Upgrade to add XML services to IQ3xcite v2.2 or greater
IQ4/IC/ADPT/10
Trend IQ4E Trend LAN Controllers
Accessories
Pack of 10 I/O bus cable adapters (for IQ4/IO modules and IQ4E controller)
IQ4/IC/ADPT/10
Trend IQ4E Controllers
Accessories
Pack of 10 I/O bus cable adapters (for IQ4/IO modules and IQ4E controller)
IQ4/IC/ADPT/2
Trend IQ4E Trend LAN Controllers
Accessories
Pack of 2 I/O bus cable adapters (for IQ4/IO modules and IQ4E controller)
IQ4/IC/LINK/5
Trend IQ4E Trend LAN Controllers
Accessories
Pack of 5 spare rigid I/O bus interconnectors (for IQ4/IO modules and IQ4E controller)
IQ4/IC/LINK/5
Trend IQ4E Controllers
Accessories
Pack of 5 spare rigid I/O bus interconnectors (for IQ4/IO modules and IQ4E controller)
IQ4/IC/TERM/5
Trend IQ4E Trend LAN Controllers
Accessories
Pack of 5 spare I/O bus terminators (for IQ4/IO modules and IQ4E controller)
IQ4/IO/16DI
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: no
DI: 16
AO: no
DO: no
UIO: no
Power: no
IQ4/IO/4DO
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: no
DI: no
AO: no
DO: 4
UIO: no
Power: no
IQ4/IO/4UIO
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: no
DI: no
AO: no
DO: no
UIO: 4
Power: no
IQ4/IO/8AO
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: no
DI: no
AO: 8
DO: no
UIO: no
Power: no
IQ4/IO/8DI
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: no
DI: 8
AO: no
DO: no
UIO: no
Power: no
IQ4/IO/8DO
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: no
DI: no
AO: no
DO: 8
UIO: no
Power: no
IQ4/IO/8UI
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: 8
DI: no
AO: no
DO: no
UIO: no
Power: no
IQ4/IO/8UIO
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
I/O Modules
UI: no
DI: no
AO: no
DO: no
UIO: 8
Power: no
IQ411/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: no
BACnet IP: no
Power: 230V
IQ411/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: no
BACnet IP: no
Power: 24V
IQ411/BAC/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: no
BACnet IP: yes
Power: 230V
IQ411/BAC/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: no
BACnet IP: yes
Power: 24V
IQ411/LAN/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: yes
BACnet IP: no
Power: 230V
IQ411/LAN/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: yes
BACnet IP: no
Power: 24V
IQ411/LAN/BAC/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: yes
BACnet IP: yes
Power: 230V
IQ411/LAN/BAC/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ411 controllers, (all models have ethernet connectivity and 3UIs and 2DIs)
DO: 6
AO: no
Trend LAN: yes
BACnet IP: yes
Power: 24V
IQ412/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: no
BACnet IP: no
Power: 230V
IQ412/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: no
BACnet IP: no
Power: 24V
IQ412/BAC/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: no
BACnet IP: yes
Power: 230V
IQ412/BAC/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: no
BACnet IP: yes
Power: 24V
IQ412/LAN/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: yes
BACnet IP: no
Power: 230V
IQ412/LAN/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: yes
BACnet IP: no
Power: 24V
IQ412/LAN/BAC/230
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: yes
BACnet IP: yes
Power: 230V
IQ412/LAN/BAC/24VAC
Trend IQ411 and IQ412 Controllers
The IQ41x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ41x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 5 inputs and 6 outputs. The IQ411 has 6 solid state digital outputs, and the IQ412 has 4 solid state digital outputs and two 0 to 10 V outputs. The IQ41x series use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
Features to replace IQ211, IQ212, and IQ7x Series controllers
Retrofit mounting plate and cable extender accessories
DIN43880 standard enclosure
UI: 3
DI: 2
Ethernet: yes
IQ412 controllers, (all models have ethernet connectivity and 3UIs and 2DIs) note: 24V vers. available from Sept 2012
DO: 4
AO: 2
Trend LAN: yes
BACnet IP: yes
Power: 24V
IQ41x ADAPTOR PLATE/20
Trend IQ411 and IQ412 Controllers
Accessories
Retrofit mounting plate to facilitate replacement of IQ21x or IQ7x - Pack of 20
IQ41x LAN CABLE EXTENDER/20
Trend IQ411 and IQ412 Controllers
Accessories
Lan cable extender to facilitate replacement of IQ21x or IQ7x - Pack of 20
IQ422/00/XNC/BAC/230
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/00
UI: no
AO: no
Network: TCP/IP
Maximum expansion: no expansion
Power: 230Vac
IQ422/00/XNC/BAC/24VAC
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/00
UI: no
AO: no
Network: TCP/IP
Maximum expansion: no expansion
Power: 24Vac
IQ422/00/XNC/LAN/BAC/230
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/00
UI: no
AO: no
Network: TCP/IP + Trend LAN
Maximum expansion: no expansion
Power: 230Vac
IQ422/00/XNC/LAN/BAC/24VAC
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/00
UI: no
AO: no
Network: TCP/IP + Trend LAN
Maximum expansion: no expansion
Power: 24Vac
IQ422/12/230
Trend IQ422 Controllers
The IQ422 intelligent controllers are designed for universal use in building control systems. Full compatibility with other Trend IQ controllers enables the IQ422 to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 6 universal inputs and 6 analogue voltage outputs. IQ422 controllers use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
UI: 6
AO: 6
Ethernet: yes
IQ422 controllers, (all models have ethernet connectivity and 6UI and 6AO)
Trend LAN: no
BACnet IP: no
Power: 230V
IQ422/12/24VAC
Trend IQ422 Controllers
The IQ422 intelligent controllers are designed for universal use in building control systems. Full compatibility with other Trend IQ controllers enables the IQ422 to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 6 universal inputs and 6 analogue voltage outputs. IQ422 controllers use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
UI: 6
AO: 6
Ethernet: yes
IQ422 controllers, (all models have ethernet connectivity and 6UI and 6AO)
Trend LAN: no
BACnet IP: no
Power: 24V
IQ422/12/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ422 Controllers
UI: 6
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ422/12/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ422 Controllers
UI: 6
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ422/12/LAN /230
Trend IQ422 Controllers
The IQ422 intelligent controllers are designed for universal use in building control systems. Full compatibility with other Trend IQ controllers enables the IQ422 to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 6 universal inputs and 6 analogue voltage outputs. IQ422 controllers use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
UI: 6
AO: 6
Ethernet: yes
IQ422 controllers, (all models have ethernet connectivity and 6UI and 6AO)
Trend LAN: yes
BACnet IP: no
Power: 230V
IQ422/12/LAN /24VAC
Trend IQ422 Controllers
The IQ422 intelligent controllers are designed for universal use in building control systems. Full compatibility with other Trend IQ controllers enables the IQ422 to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 6 universal inputs and 6 analogue voltage outputs. IQ422 controllers use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
UI: 6
AO: 6
Ethernet: yes
IQ422 controllers, (all models have ethernet connectivity and 6UI and 6AO)
Trend LAN: yes
BACnet IP: no
Power: 24V
IQ422/12/LAN /BAC/230
Trend IQ422 Controllers
The IQ422 intelligent controllers are designed for universal use in building control systems. Full compatibility with other Trend IQ controllers enables the IQ422 to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 6 universal inputs and 6 analogue voltage outputs. IQ422 controllers use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
UI: 6
AO: 6
Ethernet: yes
IQ422 controllers, (all models have ethernet connectivity and 6UI and 6AO)
Trend LAN: yes
BACnet IP: yes
Power: 230V
IQ422/12/LAN /BAC/24VAC
Trend IQ422 Controllers
The IQ422 intelligent controllers are designed for universal use in building control systems. Full compatibility with other Trend IQ controllers enables the IQ422 to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs. The controllers have 6 universal inputs and 6 analogue voltage outputs. IQ422 controllers use Ethernet and TCP/IP networking technologies with embedded XML. Trend current loop Lan, and BACnet over IP communications are available as options.
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
Trend current loop Lan option
BACnet over IP option to B-BC profile
Compatible with existing IQ system protocol
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
UI: 6
AO: 6
Ethernet: yes
IQ422 controllers, (all models have ethernet connectivity and 6UI and 6AO)
Trend LAN: yes
BACnet IP: yes
Power: 24V
IQ422/12/LAN/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ422 Trend Lan Controllers
UI: 6
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ422/12/LAN/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ422 Trend Lan Controllers
UI: 6
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ422/12/XNC/BAC/230
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/12
UI: 6
AO: 6
Network: TCP/IP
Maximum expansion: no expansion
Power: 230Vac
IQ422/12/XNC/BAC/24VAC
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/12
UI: 6
AO: 6
Network: TCP/IP
Maximum expansion: no expansion
Power: 24Vac
IQ422/12/XNC/LAN/BAC/230
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/12
UI: 6
AO: 6
Network: TCP/IP + Trend LAN
Maximum expansion: no expansion
Power: 230Vac
IQ422/12/XNC/LAN/BAC/24VAC
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ422/12
UI: 6
AO: 6
Network: TCP/IP + Trend LAN
Maximum expansion: no expansion
Power: 24Vac
IQ4E/128-160/UP
Trend IQ4E Trend LAN Controllers
Accessories
Upgrade from 128 to 160 channels
IQ4E/128/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/128/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/128/LAN/BAC/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/128/LAN/BAC/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/16-32/UP
Trend IQ4E Trend LAN Controllers
Accessories
Upgrade from 16 to 32 channels
IQ4E/16/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/16/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/16/LAN/BAC/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/16/LAN/BAC/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/160-192/UP
Trend IQ4E Trend LAN Controllers
Accessories
Upgrade from 160 to 192 channels
IQ4E/160/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/160/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/160/LAN/BAC/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/160/LAN/BAC/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/192/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/192/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/192/LAN/BAC/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/192/LAN/BAC/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/32-64/UP
Trend IQ4E Trend LAN Controllers
Accessories
Upgrade from 32 to 64 channels
IQ4E/32/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/32/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/32/LAN/BAC/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/32/LAN/BAC/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/64-96/UP
Trend IQ4E Trend LAN Controllers
Accessories
Upgrade from 64 to 96 channels
IQ4E/64/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/64/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/64/LAN/BAC/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/64/LAN/BAC/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/96-128/UP
Trend IQ4E Trend LAN Controllers
Accessories
Upgrade from 96 to 128 channels
IQ4E/96/BAC/230
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/96/BAC/24VAC
Trend IQ4E Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: TCP/IP
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/96/LAN/BAC/230
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 230Vac
IQ4E/96/LAN/BAC/24VAC
Trend IQ4E Trend LAN Controllers
The IQ4E controller has 10 universal inputs and 6 analogue voltage outputs and is expandable up to 192 points (depending on the controller variant) by adding I/O modules. This flexibility makes it suitable for a broad range of applications. The IQ4E controller uses Ethernet and TCP/IP networking technologies with embedded XML and is fully compatible with other Trend IQ controllers. The IQ4E supports BACnet over IP as standard. Trend communications over a current loop LAN is available as an option. A local PC or display (e.g. IQView4) can be connected to the RS232 port. A Wallbus port is also provided for use with room displays.
Network: Trend LAN
The following features are available:
16 onboard I/O channels - 10 inputs and 6 outputs
I/O bus supports up to a total of 192 I/O channels (depending on the controller variant) using additional I/O modules
I/O bus length up to 300 m (328 yards)
Ethernet 10/100 Mbps main network with TCP/IP protocol
Embedded XML Web Services as standard
BACnet over IP to B-BC profile
Small footprint with DIN rail mounting for DIN 19 size 2 standard enclosure
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ4 equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ4 training course.
The IQ4 Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.
IQ4E BACnet Controllers, expandible to a maximum of 192 extra points or 30 I/O Modules
UI: 10
DI: no
AO: 6
DO: no
UIO: no
Power: 24Vac
IQ4E/96/XNC/BAC/230
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ4E/96
UI: 10
AO: 6
Network: TCP/IP
Maximum expansion: 30 modules, 80 points
Power: 230Vac
IQ4E/96/XNC/BAC/24VAC
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ4E/96
UI: 10
AO: 6
Network: TCP/IP
Maximum expansion: 30 modules, 80 points
Power: 24Vac
IQ4E/96/XNC/LAN/BAC/230
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ4E/96
UI: 10
AO: 6
Network: TCP/IP + Trend LAN
Maximum expansion: 30 modules, 80 points
Power: 230Vac
IQ4E/96/XNC/LAN/BAC/24VAC
Trend IQ4 Integration Controllers
The IQ4s XNC functionality provides a way of interfacing the Trend system with 3rd party systems. It utilises standard IQ strategy modules, and the Trend Custom Language (TCL) to present information from other systems as though it is from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from Trend supervisors and software tools. The IQ422/00/XNC/.. has no I/O channels, but IQ422/12/XNC/.. has 12, and the IQ4E/96/XNC/.. has 16 I/O channels.
The product also includes:
All standard IQ4 features including BACnet over IP to B-BC profile
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)
Integration possible with: RS485
IQ4E/96
UI: 10
AO: 6
Network: TCP/IP + Trend LAN
Maximum expansion: 30 modules, 80 points
Power: 24Vac
IQ4NC/00/230
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 0
AO: 0
IQ4NC/00/24VAC
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 0
AO: 0
IQ4NC/12/230
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 6
AO: 6
IQ4NC/12/24VAC
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 6
AO: 6
IQ4NC/16/XNC/230
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 10
AO: 6
IQ4NC/16/XNC/24VAC
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 10
AO: 6
IQ4NC/32/XNC/230
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 10
AO: 6
IQ4NC/32/XNC/24VAC
Trend IQ4NC controllers
The IQ4NC enables Trend networks on different media (either Ethernet, Trend current loop, or MS/TP) to be joined together in various configurations. It provides 4 virtual CNCs which allow supervisors or tools on the Ethernet network to connect to the Trend system.
Features include:
Ethernet 10/100 Mbps main network with TCP/IP protocol
Provide Trend system interface with MS/TP trunk
Extend Trend network from Ethernet to Trend current loop
INC alarm forwarding (e.g. enabling IQeco alarms to be forwarded to an IP address)
Compatible with existing IQ system protocol
BACnet over MS/TP
BACnet over IP to B-BC profile
230 Vac or 24 Vac input power supply options
Small footprint with DIN rail mounting
RS232 and USB local supervisor ports
DIN43880 standard enclosure
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Ethernet: yes
Trend LAN: yes
BACnet IP: yes
IQ4NC controllers
UI: 10
AO: 6
IQE/PROG/UP
Trend IQeco31 controller 24V version
Accessories
Upgrade licence to convert a fixed strategy controller to a programmable controller.
IQE31/C/BAC/Custom/230
Trend IQeco31 Custom
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 31
Programability: Programmable
Control: Custom strategy
Power: 230V
IQE31/C/BAC/Custom/24VAC
Trend IQeco31 Custom
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 31
Programability: Programmable
Control: Custom strategy
Power: 24V
IQE31/F/BAC/1SFANAR2B/230
Trend IQeco31 FCU 1S Fan AR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE31/F/BAC/1SFANAR2B/24VAC
Trend IQeco31 FCU 1S Fan AR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE31/F/BAC/1SFANWR2B/230
Trend IQeco31 FCU 1S Fan WR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE31/F/BAC/1SFANWR2B/24VAC
Trend IQeco31 FCU 1S Fan WR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE31/F/BAC/1SFANWR4B/230
Trend IQeco31 FCU 1S Fan WR4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE31/F/BAC/1SFANWR4B/24VAC
Trend IQeco31 FCU 1S Fan WR4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE31/F/BAC/1SFANWT4B/230
Trend IQeco31 1S FAN WT4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE31/F/BAC/1SFANWT4B/24VAC
Trend IQeco31 1S FAN WT4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE31/F/BAC/ECFANWR2P/230
Trend IQeco31 EC FAN WR2 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.3: Plus
Units: Metric
Programability: Fixed
Power: 230V
IQE31/F/BAC/ECFANWR2P/24VAC
Trend IQeco31 EC FAN WR2 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.3: Plus
Units: Metric
Programability: Fixed
Power: 24V
IQE31/F/BAC/ECFANWR4P/230
Trend IQeco31 EC FAN WR4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE31/F/BAC/ECFANWR4P/24VAC
Trend IQeco31 EC FAN WR4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE31/F/BAC/ECFANWT2P/230
Trend IQeco31 EC FAN WT2 P
The IQECO31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE31/F/BAC/ECFANWT2P/24VAC
Trend IQeco31 EC FAN WT2 P
The IQECO31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE31/F/BAC/ECFANWT4P/230
Trend IQeco31 EC Fan WT4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE31/F/BAC/ECFANWT4P/24VAC
Trend IQeco31 EC Fan WT4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE31/F/BAC/NOSTRATEGY/230
Trend IQeco31 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy
Programability: Fixed
Power: 230V
IQE31/F/BAC/NOSTRATEGY/24VAC
Trend IQeco31 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy
Programability: Fixed
Power: 24V
IQE31/P/BAC/1SFANAR2B/230
Trend IQeco31 FCU 1S Fan AR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE31/P/BAC/1SFANAR2B/24VAC
Trend IQeco31 FCU 1S Fan AR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE31/P/BAC/1SFANWR2B/230
Trend IQeco31 FCU 1S Fan WR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE31/P/BAC/1SFANWR2B/24VAC
Trend IQeco31 FCU 1S Fan WR2 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE31/P/BAC/1SFANWR4B/230
Trend IQeco31 FCU 1S Fan WR4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE31/P/BAC/1SFANWR4B/24VAC
Trend IQeco31 FCU 1S Fan WR4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE31/P/BAC/1SFANWT4B/230
Trend IQeco31 1S FAN WT4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE31/P/BAC/1SFANWT4B/24VAC
Trend IQeco31 1S FAN WT4 B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE31/P/BAC/ECFANWR2P/230
Trend IQeco31 EC FAN WR2 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.3: Plus
Units: Metric
Programability: Programmable
Power: 230V
IQE31/P/BAC/ECFANWR2P/24VAC
Trend IQeco31 EC FAN WR2 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.3: Plus
Units: Metric
Programability: Programmable
Power: 24V
IQE31/P/BAC/ECFANWR4P/230
Trend IQeco31 EC FAN WR4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE31/P/BAC/ECFANWR4P/24VAC
Trend IQeco31 EC FAN WR4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE31/P/BAC/ECFANWT2P/230
Trend IQeco31 EC FAN WT2 P
The IQECO31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE31/P/BAC/ECFANWT2P/24VAC
Trend IQeco31 EC FAN WT2 P
The IQECO31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE31/P/BAC/ECFANWT4P/230
Trend IQeco31 EC Fan WT4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE31/P/BAC/ECFANWT4P/24VAC
Trend IQeco31 EC Fan WT4 P
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE31/P/BAC/NOSTRATEGY/230
Trend IQeco31 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy
Programability: Programmable
Power: 230V
IQE31/P/BAC/NOSTRATEGY/24VAC
Trend IQeco31 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy
Programability: Programmable
Power: 24V
IQE32/C/BAC/Custom/230
Trend IQeco32 controller 230V version
The IQECO32 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices via an IQ4NC. It has 9 I/O channels and can be supplied with custom strategies or as a programmable unit with no strategy.
Programmable: This IQECO version is fully programmable using IQ SET. This programmable controller will be supplied with no strategy. The standard strategies are available in IQ SET as solutions and can be downloaded directly or modified as required in the normal way.
Custom: The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into a controller.
UI: 1
DI: 1
TI: 2
AO: 4
DO: 0
Relay outputs: 1
Auxiliary output signal: 24 Vdc
Power supply: 230 Vac
Controllers
Control: Custom strategy
Programability: Custom
IQE32/C/BAC/Custom/24VAC
Trend IQeco32 controller 24V version
The IQECO32 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices via an IQ4NC. It has 9 I/O channels and can be supplied with custom strategies or as a programmable unit with no strategy.
Programmable: This IQECO version is fully programmable using IQ SET. This programmable controller will be supplied with no strategy. The standard strategies are available in IQ SET as solutions and can be downloaded directly or modified as required in the normal way.
Custom: The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into a controller.
UI: 1
DI: 1
TI: 2
AO: 4
DO: 0
Relay outputs: 1
Power supply: 24 Vac
Controllers
Control: Custom strategy
Programability: Custom
IQE32/P/BAC/NOSTRATEGY/230
Trend IQeco32 controller 230V version
The IQECO32 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices via an IQ4NC. It has 9 I/O channels and can be supplied with custom strategies or as a programmable unit with no strategy.
Programmable: This IQECO version is fully programmable using IQ SET. This programmable controller will be supplied with no strategy. The standard strategies are available in IQ SET as solutions and can be downloaded directly or modified as required in the normal way.
Custom: The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into a controller.
UI: 1
DI: 1
TI: 2
AO: 4
DO: 0
Relay outputs: 1
Auxiliary output signal: 24 Vdc
Power supply: 230 Vac
Controllers
Control: No strategy
Programability: Programmable
IQE32/P/BAC/NOSTRATEGY/24VAC
Trend IQeco32 controller 24V version
The IQECO32 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices via an IQ4NC. It has 9 I/O channels and can be supplied with custom strategies or as a programmable unit with no strategy.
Programmable: This IQECO version is fully programmable using IQ SET. This programmable controller will be supplied with no strategy. The standard strategies are available in IQ SET as solutions and can be downloaded directly or modified as required in the normal way.
Custom: The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into a controller.
UI: 1
DI: 1
TI: 2
AO: 4
DO: 0
Relay outputs: 1
Power supply: 24 Vac
Controllers
Control: No strategy
Programability: Programmable
IQE35/C/BAC/CUSTOM/230
Trend IQeco35 controller 230V version
The IQECO35 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. It has 17 I/O channels, and can be supplied as a fixed or programmable unit, with Trend written strategies, custom strategies or no strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The programmable units allow the strategy to be modified to meet specific project requirements whereas the fixed units can only be used with a Trend supplied strategy.
The strategy itself defines the units HVAC control method. Various Trend strategies are available and they are divided into three categories, Entry, Basic and Plus. The Entry category has less sophisticated strategies with a lower level of I/O control and the Plus category has more sophisticated strategies with the highest level of I/O control.
Trend provide a service to supply personal strategies preloaded into the IQECO. This can significantly reduce time on site by removing the need to download the same strategy to potentially several hundred controllers.
Units defined as No Strategy are supplied empty and can have strategies downloaded from SET.
UI: 3
DI: 2
TI: 3
AO: 1
DO: 4
Relay outputs: 4
Auxiliary output signal: 1 x 24 Vdc
Power supply: 230 Vac
Controllers
Application: no
Control: Custom strategy
Programability: Fixed
Additional functions: no
IQE35/C/BAC/CUSTOM/24VAC
Trend IQeco35 controller 24V version
The IQECO35 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. It has 17 I/O channels, and can be supplied as a fixed or programmable unit, with Trend written strategies, custom strategies or no strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The programmable units allow the strategy to be modified to meet specific project requirements whereas the fixed units can only be used with a Trend supplied strategy.
The strategy itself defines the units HVAC control method. Various Trend strategies are available and they are divided into three categories, Entry, Basic and Plus. The Entry category has less sophisticated strategies with a lower level of I/O control and the Plus category has more sophisticated strategies with the highest level of I/O control.
Trend provide a service to supply personal strategies preloaded into the IQECO. This can significantly reduce time on site by removing the need to download the same strategy to potentially several hundred controllers.
Units defined as No Strategy are supplied empty and can have strategies downloaded from SET.
UI: 3
DI: 2
TI: 3
AO: 1
DO: 4
Relay outputs: 4
Auxiliary output signal: 1 x 24 Vdc
Power supply: 24 Vac
Controllers
Application: no
Control: Custom strategy
Programability: Fixed
Additional functions: no
IQE35/C/BAC/Custom/230
Trend IQeco35 Custom
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 35
Programability: Programmable
Control: Custom strategy
Power: 230V
IQE35/C/BAC/Custom/24VAC
Trend IQeco35 Custom
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 35
Programability: Programmable
Control: Custom strategy
Power: 24V
IQE35/F/BAC/3SFANWR2E/230
Trend IQeco35 FCU 3S Fan WR2 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE35/F/BAC/3SFANWR2E/24VAC
Trend IQeco35 FCU 3S Fan WR2 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE35/F/BAC/3SFANWR4E/230
Trend IQeco35 FCU 3S Fan WR4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE35/F/BAC/3SFANWR4E/24VAC
Trend IQeco35 FCU 3S Fan WR4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE35/F/BAC/3SFANWR4EB/230
Trend IQeco35 FCU 3S Fan WR4 E B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE35/F/BAC/3SFANWR4EB/24VAC
Trend IQeco35 FCU 3S Fan WR4 E B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE35/F/BAC/3SFANWT4E/230
Trend IQeco35 3S FAN WT4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 230V
IQE35/F/BAC/3SFANWT4E/24VAC
Trend IQeco35 3S FAN WT4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Fixed
Power: 24V
IQE35/F/BAC/NOSTRATEGY/230
Trend IQeco35 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy
Programability: Fixed
Power: 230V
IQE35/F/BAC/NOSTRATEGY/24VAC
Trend IQeco35 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy
Programability: Fixed
Power: 24V
IQE35/P/BAC/3SFANWR2E/230
Trend IQeco35 FCU 3S Fan WR2 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE35/P/BAC/3SFANWR2E/24VAC
Trend IQeco35 FCU 3S Fan WR2 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE35/P/BAC/3SFANWR4E/230
Trend IQeco35 FCU 3S Fan WR4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE35/P/BAC/3SFANWR4E/24VAC
Trend IQeco35 FCU 3S Fan WR4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE35/P/BAC/3SFANWR4EB/230
Trend IQeco35 FCU 3S Fan WR4 E B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE35/P/BAC/3SFANWR4EB/24VAC
Trend IQeco35 FCU 3S Fan WR4 E B
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE35/P/BAC/3SFANWT4E/230
Trend IQeco35 3S FAN WT4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 230V
IQE35/P/BAC/3SFANWT4E/24VAC
Trend IQeco35 3S FAN WT4 E
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric
Availability: Pre-installed/download
Programability: Programmable
Power: 24V
IQE35/P/BAC/NOSTRATEGY/230
Trend IQeco35 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy
Programability: Programmable
Power: 230V
IQE35/P/BAC/NOSTRATEGY/24VAC
Trend IQeco35 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy
Programability: Programmable
Power: 24V
IQE38/C/BAC/Custom/230
Trend IQeco38 Custom
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 38
Programability: Programmable
Control: Custom strategy
Power: 230V
IQE38/C/BAC/Custom/24VAC
Trend IQeco38 Custom
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The IQECO can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQECO controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 38
Programability: Programmable
Control: Custom strategy
Power: 24V
IQE38/F/BAC/NOSTRATEGY/230
Trend IQeco38 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy
Programability: Fixed
Power: 230V
IQE38/F/BAC/NOSTRATEGY/24VAC
Trend IQeco38 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy
Programability: Fixed
Power: 24V
IQE38/P/BAC/NOSTRATEGY/230
Trend IQeco38 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy
Programability: Programmable
Power: 230V
IQE38/P/BAC/NOSTRATEGY/24VAC
Trend IQeco38 No Strategy
The IQECO31, 32, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQECOs over the BACnet MS/TP network, and with Trend networked devices by using an IQ4NC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQECO can be purchased either as a fully programmable or a fixed strategy model. A wide range of strategies can be downloaded to the units to provide pre-configured functionality for a host of different applications. They are classified as Entry level (E), Basic (B) or Plus (P)and can be downloaded into the respective controllers. The more popular application strategies can be ordered directly from the factory. Please see price list for details. The fixed strategy controllers will allow a degree of configuration while the programmable models allow complete flexibility. Should it be necessary to upgrade from a fixed to programmable an unlock is available.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy
Programability: Programmable
Power: 24V
IQEVAVP/P/BAC/VAV2E/24VAC
Trend IQeco VAV2E
The IQECO variable air volume standard strategy controls a proportional damper, an on/off fan (either serial or parallel), and two stages of electric heating in response to a thermistor temperature sensor with a local setpoint knob. The 2E strategy is for on/off electric heating. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
The IQECOVAVP is fitted with a differential air pressure transducer. The IQECOVAVPA is fitted with a differential air pressure transducer and an actuator.
Model: IQeco VAVP
Programability: Programmable
Application: VAV
Control: VAV 2 Stage Electric Heater
Units: Metric
Power: 24V
Additional functions: no
IQEVAVPA/P/BAC/VAV2E/24VAC
Trend IQeco VAV2E
The IQECO variable air volume standard strategy controls a proportional damper, an on/off fan (either serial or parallel), and two stages of electric heating in response to a thermistor temperature sensor with a local setpoint knob. The 2E strategy is for on/off electric heating. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
The IQECOVAVP is fitted with a differential air pressure transducer. The IQECOVAVPA is fitted with a differential air pressure transducer and an actuator.
Model: IQeco VAVP
Programability: Programmable
Application: VAV
Control: VAV 2 Stage Electric Heater
Units: Metric
Power: 24V
Additional functions: Fitted Actuator
IQV-1-N
Trend IQVISION SUPERVISOR
TONN Points
Upgrade Supervisor add 1 TONN connectivity
IQV-10-N
Trend IQVISION SUPERVISOR
TONN Points
Upgrade Supervisor add 10 TONN connectivity
IQV-10000-OPEN
Trend IQVISION SUPERVISOR
Open Points
Extend base license with additional 10000 Open protocols points
IQV-100EXT
Trend IQVISION SUPERVISOR
Additional Trend Points
Additional 100 Trend Database Points
IQV-15000
Trend IQVISION SUPERVISOR
IQVISION is a building monitoring and management solution built upon the powerful Niagara 4 platform. It is capable of integrating Trend controllers, third party devices and internet protocols into a centralised software platform that is designed to manage buildings at an enterprise level.
IQVISION serves real-time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, trending, master scheduling, system-wide database management, and integration with enterprise software applications - all of which can be used for highlighting and investigating energy use with in buildings.
In addition, IQVISION provides a comprehensive, graphical engineering toolset for application development. HTML5 support enables the customisation of user interfaces that are viewable on diverse web-enabled computers, tablets and phones.
Third party device integration using open standard protocols such as BACnet, Modbus, MBUS and KNX is also supported.
Model: IQVISION 15000 Trend point included
IQV-15000EXT
Trend IQVISION SUPERVISOR
Additional Trend Points
Additional 15000 Trend Database Points
IQV-2500
Trend IQVISION SUPERVISOR
IQVISION is a building monitoring and management solution built upon the powerful Niagara 4 platform. It is capable of integrating Trend controllers, third party devices and internet protocols into a centralised software platform that is designed to manage buildings at an enterprise level.
IQVISION serves real-time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, trending, master scheduling, system-wide database management, and integration with enterprise software applications - all of which can be used for highlighting and investigating energy use with in buildings.
In addition, IQVISION provides a comprehensive, graphical engineering toolset for application development. HTML5 support enables the customisation of user interfaces that are viewable on diverse web-enabled computers, tablets and phones.
Third party device integration using open standard protocols such as BACnet, Modbus, MBUS and KNX is also supported.
Model: IQVISION 2500 Trend point included
IQV-2500-OPEN
Trend IQVISION SUPERVISOR
Open Points
Extend base license with additional 2500 Open protocols points
IQV-2500EXT
Trend IQVISION SUPERVISOR
Additional Trend Points
Additional 2500 Trend Database Points
IQV-500
Trend IQVISION SUPERVISOR
IQVISION is a building monitoring and management solution built upon the powerful Niagara 4 platform. It is capable of integrating Trend controllers, third party devices and internet protocols into a centralised software platform that is designed to manage buildings at an enterprise level.
IQVISION serves real-time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, trending, master scheduling, system-wide database management, and integration with enterprise software applications - all of which can be used for highlighting and investigating energy use with in buildings.
In addition, IQVISION provides a comprehensive, graphical engineering toolset for application development. HTML5 support enables the customisation of user interfaces that are viewable on diverse web-enabled computers, tablets and phones.
Third party device integration using open standard protocols such as BACnet, Modbus, MBUS and KNX is also supported.
Model: IQVISION 500 Trend point included
IQV-500-OPEN
Trend IQVISION SUPERVISOR
Open Points
Extend base license with additional 500 Open protocols points
IQV-5000
Trend IQVISION SUPERVISOR
IQVISION is a building monitoring and management solution built upon the powerful Niagara 4 platform. It is capable of integrating Trend controllers, third party devices and internet protocols into a centralised software platform that is designed to manage buildings at an enterprise level.
IQVISION serves real-time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, trending, master scheduling, system-wide database management, and integration with enterprise software applications - all of which can be used for highlighting and investigating energy use with in buildings.
In addition, IQVISION provides a comprehensive, graphical engineering toolset for application development. HTML5 support enables the customisation of user interfaces that are viewable on diverse web-enabled computers, tablets and phones.
Third party device integration using open standard protocols such as BACnet, Modbus, MBUS and KNX is also supported.
Model: IQVISION 5000 Trend point included
IQV-5000-OPEN
Trend IQVISION SUPERVISOR
Open Points
Extend base license with additional 5000 Open protocols points
IQV-50000
Trend IQVISION SUPERVISOR
IQVISION is a building monitoring and management solution built upon the powerful Niagara 4 platform. It is capable of integrating Trend controllers, third party devices and internet protocols into a centralised software platform that is designed to manage buildings at an enterprise level.
IQVISION serves real-time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, trending, master scheduling, system-wide database management, and integration with enterprise software applications - all of which can be used for highlighting and investigating energy use with in buildings.
In addition, IQVISION provides a comprehensive, graphical engineering toolset for application development. HTML5 support enables the customisation of user interfaces that are viewable on diverse web-enabled computers, tablets and phones.
Third party device integration using open standard protocols such as BACnet, Modbus, MBUS and KNX is also supported.
Model: IQVISION 50000 Trend point included
IQV-5000EXT
Trend IQVISION SUPERVISOR
Additional Trend Points
Additional 5000 Trend Database Points
IQV-500EXT
Trend IQVISION SUPERVISOR
Additional Trend Points
Additional 500 Trend Database Points
IQV-ALM-PORTAL
Trend IQVISION SUPERVISOR
Extended Support Options
IQV remote alarm portal
IQV-DB-CSV
Trend IQVISION SUPERVISOR
Extended Support Options
Extend the capability for the supervisor to interact with Microsoft Excel
IQV-DB-SQL
Trend IQVISION SUPERVISOR
Extended Support Options
Extend the capability for the supervisor to communicate SQL
IQV-MNT1
Trend IQVISION SUPERVISOR
Maintenance Upgrade Options
IQVISION maintenance upgrade - additional 1 year
IQV-MNT3
Trend IQVISION SUPERVISOR
Maintenance Upgrade Options
IQVISION maintenance upgrade - additional 3 year
IQV-MNT5
Trend IQVISION SUPERVISOR
Maintenance Upgrade Options
IQVISION maintenance upgrade - additional 5 year
IQV-OPC
Trend IQVISION SUPERVISOR
Extended Support Options
Extend the open protocol points with OPC connectivity
IQVIEW4 SM BOX
Trend IQView4 Local Touch Screen Display
Accessories
Surface Mount Box for mounting the IQView4 on wall or panel
IQVIEW4/24
Trend IQView4 Local Touch Screen Display
The IQView4 is a touch screen display which provides an interface to an IQ controller by way of its local supervisor port. It allows access to modules, graphs, alarms, and timezones.
It has a 4.3 (109.2 mm) LCD touch screen colour display, and is housed with the electronics in a single unit suitable for rear panel mount applications. As well as a Home screen, the unit can be programmed with a number of favourite screens.
RS232 connection options
Rear panel mount with front cover
24 Vac/dc input power supply
Colour touch screen display
Connects directly to IQ controller local supervisor port
Compatible with IQ1s (v5 and above), IQ2s, IQ3s
Key click sounder
View of inputs, outputs, directories, logs
Adjustment of knobs, switches, time zones, time
IQVIEW4/FPK ADAPTOR PLATE
Trend IQView4 Local Touch Screen Display
Accessories
Adaptor plate to facilitate mounting an IQView4 in place of FPK (2 line display panel, front panel kit)
IQVIEW8 DRY PARTITION WALL BOX
Trend IQView8 Touch Screen Display
Accessories
Kit for mounting IQView8 embedded in an dry partition wall.
IQVIEW8 SURFACE MOUNTING BOX
Trend IQView8 Touch Screen Display
Accessories
Kit for mounting IQView8 on a flat surface or double UK or USA pattress box.
IQVIEW8/24
Trend IQView8 Touch Screen Display
The IQView8 is a touch screen display which provides an interface to the Trend system. It enables the user to view and adjust operating times, monitor alarms, make adjustments to controller parameters, and display graphs of logged data. Schematic displays provide the ability to view, change and graph data from colour graphics pages. Alarms can be sent directly to the IQView8 where they appear on a special display, where an audible, and visual indication of the alarm is given. Three mounting options allow the unit to be panel mounted, surface mounted or embedded in a dry partion wall. A relay output is available for use with an alarm sounder.
Features include:
8 16:9 colour touch screen LCD display
Colour graphics pages (schematic)
2GB memory card.
Permits adjustment of knobs, switches, time zones and graphing of logged data
Configurable users to ensure system security
Communicates with all controllers on network (not autodialled networks)
DHCP enabled
Ethernet, current loop Lan, or RS232 network connection
Panel, surface, or embedded mounting
IQView4
Trend IQ411 and IQ412 Controllers
Related products
Touch screen colour display giving access to modules, graphs, alarms, and timezones.
LF-MF
Trend Air duct and immersion temperature sensor, NTC
Flange
Mounting flange for air-duct application (10 pieces)
LLO
Trend Light Level Sensor
Light Level Sensor is an accurate lux calibrated light level sensor which can be used for monitoring and control applications. The signal output is 4 to 20 mA loop powered and the lux range is selectable at installation from the following: 0 to 1000, 0 to 2000, 0 to 4000, 0 to 8000, or 0 to 20000 lux.
Mounting place: wall outside
Protection class: IP65 Housing
LLS
Trend Light Level Sensor
Light Level Sensor is an accurate lux calibrated light level sensor which can be used for monitoring and control applications. The signal output is 4 to 20 mA loop powered and the lux range is selectable at installation from the following: 0 to 1000, 0 to 2000, 0 to 4000, 0 to 8000, or 0 to 20000 lux.
Mounting place: internal wall
Protection class: Flame retardant polycarbonate housing
M100-AG
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN15-DN25) valves with 2.9 mm stroke
M100 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.
M100-AO
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN15-DN25) valves with 2.9 mm stroke
M100 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.
M100-BG
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN15-DN25) valves with 2.9 mm stroke
M100 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.
M44-MOD-1M
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Cable with plug, 1 meter, 3 x 0,22 mm2 (10 pieces)
M44-MOD-1M/U
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Cable with plug, 1 meter, 3 x 0,22 mm2 (1 piece)
M44-MOD-1MH
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Non-halogen cable with plug, 1 meter, 3 x 0,22 mm2 (10 pieces)
M44-MOD-1MH/U
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Non-halogen cable with plug, 1 meter, 3 x 0,22 mm2 (1 piece)
M44-MOD-3M
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Cable with plug, 3 meter, 3 x 0,22 mm2 (10 pieces)
M44-MOD-3MH
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Non-halogen cable with plug, 3 meter, 3 x 0,22 mm2 (10 pieces)
M44-MOD-5M
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Cable with plug, 5 meter, 3 x 0,22 mm2 (10 pieces)
M44-MOD-5MH
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)
Non-halogen cable with plug, 5 meter, 3 x 0,22 mm2 (10 pieces)
M44-VA50
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Valve Adapters M30 x 1,5
Valve adapter with closing dimension 10,5mm (10 pieces)
M4410E1510
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Electrical actuator for (radiator) valves with connection size M30 x 1,5. The actuator is supplied with the M44-VA10 adapter (closing dimension 11,5 mm). This suits the following valves:
V58xxA4, V58xxC4, VSO
V300, V2000
V2464, V2474
A separate adapter can be ordered (M44-VA50). With this adapter the actuator fits to the valves with closing dimension 10,5 mm.
Protection class: IP54
Effective stroke for Honeywell valves 2,5 mm; maximum stroke 4 mm.
Stem force: 100N
Control input signal: 0..10V=
Stroke: 2.5mm
Power loss action: stem extends
Runtime: 75s
Cable length: optional: 1, 3 ,5m
Required materials: check accessories
2,5 mm; 100 N
Supply voltage: 24 Vac
M4410K1515
Trend Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Electrical actuator for (radiator) valves with connection size M30 x 1,5. The actuator is supplied with the M44-VA10 adapter (closing dimension 11,5 mm). This suits the following valves:
V58xxA4, V58xxC4, VSO
V300, V2000
V2464, V2474
A separate adapter can be ordered (M44-VA50). With this adapter the actuator fits to the valves with closing dimension 10,5 mm.
Protection class: IP54
Effective stroke for Honeywell valves 2,5 mm; maximum stroke 4 mm.
Stem force: 100N
Control input signal: 0..10V=
Stroke: 2.5mm
Power loss action: stem extends
Runtime: 75s
Cable length: optional: 1, 3 ,5m
Required materials: check accessories
2,5 mm; 100 N
Supply voltage: 24 Vdc
M5410L1001
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN20-DN32) valves with stroke 6.0mm
M5410 actuators fast motorized, 6.5 mm effective stroke, 100N, on/off.
M6061A1013
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 10Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 1.5min
Position feedback: no
End switches: optional
M6061A1021
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 20Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 1.6min
Position feedback: no
End switches: optional
M6061A1039
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 30Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 2.3min
Position feedback: no
End switches: optional
M6061A1047
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 40Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 3.5min
Position feedback: no
End switches: optional
M6061L1019
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 10Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 1.5min
Position feedback: no
End switches: optional
M6061L1027
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 20Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 1.6min
Position feedback: no
End switches: optional
M6061L1035
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 30Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 2.3min
Position feedback: optional
End switches: optional
M6061L1043
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Floating control
Torque: 40Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 3.5min
Position feedback: no
End switches: optional
M6410C2023
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m
M6410C2031
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 24 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m
M6410C4029
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m
M6410C4037
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 24 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m
M6410L2023
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 230 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m
M6410L2031
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 230 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m
M6410L4029
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 230 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m
M6410L4037
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 230 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m
M6422L1003
Trend Actuator for V5421B1090
Protection class: IP54
Supply voltage: 230 Vac
Control input signal: 3-pt
Built in rotation limiter: no
Manual operation: yes
End switches: optional
Runtime: 150s
Torque: 40Nm
M7061E1012
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Modulating control
Torque: 10Nm
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Runtime: 1.5min
Position feedback: optional
End switches: no
M7061E1020
Trend Standard Line Rotary Actuator
Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes
Modulating control
Torque: 20Nm
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Runtime: 3.0min
Position feedback: optional
End switches: no
M7410A1001
Trend Actuator 3-pt for terminal unit/radiator, 2,5 mm 90 N, M7410A
Electrical actuator floating control, for valve series: V135, V136, V58..A4, V58..C4, VSO.
Protection class: IP43
Position indication: with red indicator
Manual operation with valve cap.
Supply voltage: 24 Vac
Stem force: 90N
Control input signal: 3-pt
Stroke: 2.5mm
Runtime: 57s
2,5 mm; 90 N
Cable length: 0.9m
M7410A1001-3M
Trend Actuator 3-pt for terminal unit/radiator, 2,5 mm 90 N, M7410A
Electrical actuator floating control, for valve series: V135, V136, V58..A4, V58..C4, VSO.
Protection class: IP43
Position indication: with red indicator
Manual operation with valve cap.
Supply voltage: 24 Vac
Stem force: 90N
Control input signal: 3-pt
Stroke: 2.5mm
Runtime: 57s
2,5 mm; 90 N
Cable length: 3m
M7410C1007
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 1.5m
M7410C1007-10M
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 10m
M7410C1015
Trend Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410
Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 1.5m
M7410E1002
Trend Actuator 0/2..10V for zone control, 90/180/300 N, M7410E
Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=
Cable length: 1.5m
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Manual operation: no
End switches: no
Runtime: 150s
M7410E1028
Trend Actuator 0/2..10V for zone control, 90/180/300 N, M7410E
Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=
Cable length: 1.5m
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Stroke: 6.5mm
Manual operation: no
End switches: no
Runtime: 150s
M7410E2026
Trend Actuator 0/2..10V for zone control, 90/180/300 N, M7410E
Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=
Cable length: 1.5m
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Manual operation: yes
End switches: no
Runtime: 150s
M7410E2034
Trend Actuator 0/2..10V for zone control, 90/180/300 N, M7410E
Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=
Cable length: 1.5m
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Stroke: 6.5mm
Manual operation: yes
End switches: no
Runtime: 150s
M7410E4022
Trend Actuator 0/2..10V for zone control, 90/180/300 N, M7410E
Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=
Cable length: 1.5m
6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Manual operation: yes
End switches: 2
Runtime: 150s
M7410E4030
Trend Actuator 0/2..10V for zone control, 90/180/300 N, M7410E
Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=
Cable length: 1.5m
6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Stroke: 6.5mm
Manual operation: yes
End switches: 2
Runtime: 150s
M7410E5001
Trend Actuator 0/2..10V for zone control, 90/180/300 N, M7410E
Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=
Cable length: 1.5m
2,7 mm; 90 N; for valve series V5004TY. 2,5 mm; 90 N; for valve series V5822A, V5823A/C, V5832A, V5833A/C, VSO and TRV V20/V30
Stem force: 90N
Stroke: 2.5mm
Manual operation: no
End switches: no
Runtime: 70s
ML6420A3007
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N
Supply voltage: 24 Vac
Power loss action: no
Manual operation: yes
Runtime: 1.0min
Spring return: no
ML6420A3015
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N
Supply voltage: 230 Vac
Power loss action: no
Manual operation: yes
Runtime: 1.0min
Spring return: no
ML6420A3023
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N
Supply voltage: 24 Vac
Power loss action: no
Manual operation: yes
Runtime: 0.5min
Spring return: no
ML6420A3031
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N
Supply voltage: 230 Vac
Power loss action: no
Manual operation: yes
Runtime: 0.5min
Spring return: no
ML6420A3072
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N
Supply voltage: 24 Vac
Power loss action: no
Manual operation: no
Runtime: 1.0min
Spring return: no
ML6421A3005
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes
20 mm; 1800 N
Supply voltage: 24 Vac
Stroke: 20mm
Runtime: 1.9min
Position feedback: optional
ML6421A3013
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes
20 mm; 1800 N
Supply voltage: 230 Vac
Stroke: 20mm
Runtime: 1.9min
Position feedback: no
ML6421B3004
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes
38 mm; 1800 N
Supply voltage: 24 Vac
Stroke: 38mm
Runtime: 3.5min
Position feedback: optional
ML6421B3012
Trend Actuator 3-pt, 20/38 mm 1800 N, ML6421
Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes
38 mm; 1800 N
Supply voltage: 230 Vac
Stroke: 38mm
Runtime: 3.5min
Position feedback: no
ML6425A3006
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N, Spring return
Supply voltage: 24 Vac
Power loss action: stem extends
Manual operation: no
Runtime: 1.8min
Spring return: yes
ML6425A3014
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N, Spring return
Supply voltage: 230 Vac
Power loss action: stem extends
Manual operation: no
Runtime: 1.8min
Spring return: yes
ML6425B3005
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N, Spring return
Supply voltage: 24 Vac
Power loss action: stem retracts
Manual operation: no
Runtime: 1.8min
Spring return: yes
ML6425B3021
Trend Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm
20 mm; 600 N, Spring return
Supply voltage: 230 Vac
Power loss action: stem retracts
Manual operation: no
Runtime: 1.8min
Spring return: yes
ML6435B1008
Trend Actuator 3-pt for district heating, DHWS, spring return, 6,5 mm 400 N, ML6435
Electrical actuator floating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40)
Protection class: IP54
Approved according DIN EN 14597 in combination with V5825B.
Stem force: 400N
Control input signal: 3-pt
Stroke: 6.5mm
Power loss action: stem retracts
Runtime: 60s
Spring return: yes
6,5 mm; 400 N
Supply voltage: 24 Vac
ML6435B1016
Trend Actuator 3-pt for district heating, DHWS, spring return, 6,5 mm 400 N, ML6435
Electrical actuator floating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40)
Protection class: IP54
Approved according DIN EN 14597 in combination with V5825B.
Stem force: 400N
Control input signal: 3-pt
Stroke: 6.5mm
Power loss action: stem retracts
Runtime: 60s
Spring return: yes
6,5 mm; 400 N
Supply voltage: 230 Vac
ML7420A6009T
Trend Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425
Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Stroke: 20mm
20 mm; 600 N
Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: no
Manual operation: yes
Runtime: 1.0min
Spring return: no
Position feedback: 2..10V=
ML7420A6017T
Trend Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425
Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Stroke: 20mm
20 mm; 600 N
Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: no
Manual operation: yes
Runtime: 0.5min
Spring return: no
Position feedback: 2..10V=
ML7420A6025T
Trend Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425
Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Stroke: 20mm
20 mm; 600 N
Power supply: 24Vac
Control input signal: 2..10V=
Power loss action: no
Manual operation: no
Runtime: 1.0min
Spring return: no
Position feedback: no
ML7421A3004
Trend Actuator 0/2..10V, 20/38 mm 1800 N, ML7421
Electrical actuator modulating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: selectable: closed, half open, open
Position feedback: 2..10V=
End switches: optional
Supply voltage: 24 Vac
Stem force: 1800N
Control input signal: 0/2..10V=; 0/4..20mA
Manual operation: yes
20 mm; 1800 N
Stroke: 20mm
Runtime: 1.9min
ML7421B3003
Trend Actuator 0/2..10V, 20/38 mm 1800 N, ML7421
Electrical actuator modulating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: selectable: closed, half open, open
Position feedback: 2..10V=
End switches: optional
Supply voltage: 24 Vac
Stem force: 1800N
Control input signal: 0/2..10V=; 0/4..20mA
Manual operation: yes
38 mm; 1800 N
Stroke: 38mm
Runtime: 3.5min
ML7425A6008T
Trend Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425
Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Stroke: 20mm
20 mm; 600 N, Spring return
Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: stem extends
Manual operation: no
Runtime: 1.8min
Spring return: yes
Position feedback: 2..10V=
ML7425B6007T
Trend Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425
Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Stroke: 20mm
20 mm; 600 N, Spring return
Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: stem retracts
Manual operation: no
Runtime: 1.8min
Spring return: yes
Position feedback: 2..10V=
ML7430E1005
Trend Actuator 0/2..10V for district heating, DHWS, 6,5 mm 400 N, ML7430/ML7435
Electrical actuator modulating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40).
Protection class: IP54
For ML7435E1004: approved according DIN EN 14597 in combination with V5825B.
Supply voltage: 24 Vac
Stem force: 400N
Control input signal: 0/2..10V=
Stroke: 6.5mm
6,5 mm; 400 N
Power loss action: no
Manual operation: yes
Runtime: 15s
Spring return: no
ML7435E1004
Trend Actuator 0/2..10V for district heating, DHWS, 6,5 mm 400 N, ML7430/ML7435
Electrical actuator modulating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40).
Protection class: IP54
For ML7435E1004: approved according DIN EN 14597 in combination with V5825B.
Supply voltage: 24 Vac
Stem force: 400N
Control input signal: 0/2..10V=
Stroke: 6.5mm
6,5 mm; 400 N
Power loss action: stem retracts
Manual operation: no
Runtime: 60s
Spring return: yes
MT-ADAPT-HW
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Adapters
Extra mounting adapters M30 x 1,5; 10 units
MT-CABLE-10M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Plug-in cable (not for models with end switch)
Cable 10 meter; 10 units
MT-CABLE-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Plug-in cable (not for models with end switch)
Cable 2,5 meter; 10 units
MT-CABLE-5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Plug-in cable (not for models with end switch)
Cable 5 meter; 10 units
MT-CLIP
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Accessories
Extra mounting clips; 10 units
MT4-024-NC
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.2A
Cable length: 1m
MT4-024-NC-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.2A
Cable length: 2.5m
MT4-024-NO
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.2A
Cable length: 1m
MT4-024-NO-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.2A
Cable length: 2.5m
MT4-024S-NC
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN15-DN25) valves with 2.9 mm stroke
MT4 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.
MT4-024S-NO
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN15-DN25) valves with 2.9 mm stroke
MT4 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.
MT4-230-NC
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.4A
Cable length: 1m
MT4-230-NC-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.4A
Cable length: 2.5m
MT4-230-NO
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.4A
Cable length: 1m
MT4-230-NO-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 2.5mm
Runtime: 4min
Initial current: 0.4A
Cable length: 2.5m
MT4-230S-NC
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN15-DN25) valves with 2.9 mm stroke
MT4 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.
MT4-230S-NO
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN15-DN25) valves with 2.9 mm stroke
MT4 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.
MT8-024-NC
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 6.5mm
Runtime: 6min
Initial current: 0.2A
Cable length: 1m
MT8-024-NC-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 6.5mm
Runtime: 6min
Initial current: 0.2A
Cable length: 2.5m
MT8-024-NO
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 6.5mm
Runtime: 6min
Initial current: 0.2A
Cable length: 1m
MT8-024-NO-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 6.5mm
Runtime: 6min
Initial current: 0.2A
Cable length: 2.5m
MT8-024S-NC
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN20-DN32) valves with stroke 6.0mm
MT8 actuators thermoelectric, 6.5 mm effective stroke, 90N, on/off.
MT8-024S-NO
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN20-DN32) valves with stroke 6.0mm
MT8 actuators thermoelectric, 6.5 mm effective stroke, 90N, on/off.
MT8-230-NC
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 6.5mm
Runtime: 6.5min
Initial current: 0.4A
Cable length: 1m
MT8-230-NC-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 6.5mm
Runtime: 6.5min
Initial current: 0.4A
Cable length: 2.5m
MT8-230-NO
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 6.5mm
Runtime: 6.5min
Initial current: 0.4A
Cable length: 1m
MT8-230-NO-2.5M
Trend Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm
6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 6.5mm
Runtime: 6.5min
Initial current: 0.4A
Cable length: 2.5m
MT8-230S-NC
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN20-DN32) valves with stroke 6.0mm
MT8 actuators thermoelectric, 6.5 mm effective stroke, 90N, on/off.
MT8-230S-NO
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
Accessories for V5004TY Kombi QM (DN20-DN32) valves with stroke 6.0mm
MT8 actuators thermoelectric, 6.5 mm effective stroke, 90N, on/off.
MVN613A1500
Trend Rotary Actuator, MVN
Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m
Floating control
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Runtime: 108s
MVN643A1500
Trend Rotary Actuator, MVN
Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m
Floating control
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
Runtime: 30s
MVN663A1500
Trend Rotary Actuator, MVN
Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m
Floating control
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Runtime: 108s
MVN713A1500
Trend Rotary Actuator, MVN
Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m
Modulating control. Control action reversable.
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Runtime: 90s
MVNAAA/U
Trend Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves
Replacement valve adaptor standard profile, for VBG valves, DN15..DN32
MVNAT3/B
Trend Rotary Actuator, MVN
Accessories
Replacement screw terminal block, pluggable
N05010
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: no
Runtime: 90/110s
Torque: 5Nm
Damper area: 1m2
N05010-SW2
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: 2
Runtime: 90/110s
Torque: 5Nm
Damper area: 1m2
N05230-2POS
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 1 square meter
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Runtime: max. 110s
Torque: 5Nm
Damper area: 1m2
N0524
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: no
Runtime: 110s
Torque: 5Nm
Damper area: 1m2
N0524-SW2
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: 2
Runtime: 110s
Torque: 5Nm
Damper area: 1m2
N10010
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: no
Runtime: 90/110s
Torque: 10Nm
Damper area: 2m2
N10010-SW2
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: 2
Runtime: 90/110s
Torque: 10Nm
Damper area: 2m2
N10230-2POS
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 2 square meters
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Runtime: max. 140s
Torque: 10Nm
Damper area: 2m2
N1024
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: no
Runtime: 110s
Torque: 10Nm
Damper area: 2m2
N1024-SW2
Trend Damper actuator 5/10 Nm, SmartAct
Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes
For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: 2
Runtime: 110s
Torque: 10Nm
Damper area: 2m2
N20010
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 4 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Built in rotation limiter: yes
End switches: optional
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 20Nm
Damper area: 4m2
N20010-SW2
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 4 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Built in rotation limiter: yes
End switches: 2
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 20Nm
Damper area: 4m2
N20230
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 4 square meters
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2
N20230-SW2
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 4 square meters
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: 2
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2
N2024
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 4 square meters
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2
N2024-SW2
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 4 square meters
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: 2
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2
N34010
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 6 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Built in rotation limiter: no
End switches: optional
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 34Nm
Damper area: 6m2
N34230
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 6 square meters
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Built in rotation limiter: no
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 34Nm
Damper area: 6m2
N3424
Trend Damper actuator 20/34 Nm, SmartAct
Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch
When power is removed, the actuator remains in position
Removable wiring box, with cable gland M20x1,5 1/2" NPT
Actuator supplied with complete package mounting parts
For modulating control models: Control input signal can be voltage or current
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes
For damper area of 6 square meters
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Built in rotation limiter: no
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 34Nm
Damper area: 6m2
NBOX/TMNG/EUR/230
Trend Trend Modem Node Controller (TMN...)
The TMN range allows either networked or stand-alone IQ System devices to access the Public Switched Telephone Network (PSTN) via an integral or external modem, or to access the Integrated Services Digital Network (ISDN) via a terminal adaptor. The TMNG uses wireless communication via a GSM service provider enabling connections to sites without landlines and direct SMS messaging (text messages) to mobile phones. The TMN can communicate either to single or multiple devices over the IQ system current loop Lan. It also supports text messaging and communications to radiopagers via the PSTN and is supplied either boxed, or as a board which can be fitted in other IQ system devices (e.g. IQ controllers). There are high speed integral modem, GSM modem, and external modem/terminal adaptor versions.
Network: Trend LAN
Enables communication between IQ System devices over PSTN, ISDN, or GSM.
TMNG enables wireless communication and direct SMS messaging to mobile phones
Memory retains telephone numbers and settings on power fail without battery.
Can be used on IQ system current loop Lans and internetwork or direct connected to software tool or controller.
TMNH high speed integral modem has international approvals.
Fast data rate reduces transmission times.
TMNG (Trend Modem Node GSM)
Model: GSM modem
Power: 230Vac
Comments: NBOX IP30
NBOX/TMNH/UK/230
Trend Trend Modem Node Controller (TMN...)
The TMN range allows either networked or stand-alone IQ System devices to access the Public Switched Telephone Network (PSTN) via an integral or external modem, or to access the Integrated Services Digital Network (ISDN) via a terminal adaptor. The TMNG uses wireless communication via a GSM service provider enabling connections to sites without landlines and direct SMS messaging (text messages) to mobile phones. The TMN can communicate either to single or multiple devices over the IQ system current loop Lan. It also supports text messaging and communications to radiopagers via the PSTN and is supplied either boxed, or as a board which can be fitted in other IQ system devices (e.g. IQ controllers). There are high speed integral modem, GSM modem, and external modem/terminal adaptor versions.
Network: Trend LAN
Enables communication between IQ System devices over PSTN, ISDN, or GSM.
TMNG enables wireless communication and direct SMS messaging to mobile phones
Memory retains telephone numbers and settings on power fail without battery.
Can be used on IQ system current loop Lans and internetwork or direct connected to software tool or controller.
TMNH high speed integral modem has international approvals.
Fast data rate reduces transmission times.
TMNH (Trend Modem Node High speed)
Model: high speed integral modem
Power: 230Vac
Comments: NBOX IP30
NX-FAN-4
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: NXL HVAC / NXS spare part fan size 4 (HVAC03-HVAC12, NXS0003-NXS0012)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NX-FAN-5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: NXL HVAC / NXS spare part fan size 5 (HVAC16-HVAC31, NXS0016-NXS0031)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NX-FAN-6
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: NXL HVAC / NXS spare part fan size 6 (HVAC38-HVAC61, NXS0038-NXS0061)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NX-FAN-7
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Main cooling fan spare parts for inverters
Product description: NXS spare part fan size 7 (NXS0072-NXS0105)
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
NX-FAN-8
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, main fan, frame size 8, power 75 - 110 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-8-SET1
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan kit, main fan and internal fan, frame size 8, 62 - 140 A
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-8-SET2
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan kit, main fan and two internal fans, frame size 8, 168 - 205 A
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-9-FULLSET
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan kit, (main fans, 2x intern fans, fan power supply), frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-9-SET
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan set, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-INT-FR9-1
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, internal fan, 52 mm, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-INT-FR9-2
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, internal fan, 80 mm, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-INT4
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NX drives, internal fan, frame size 4, power 1.15 - 5 kW
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NX-FAN-INT5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NX drives, internal fan, frame size 5, power 7.5 - 15 kW
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NX-FAN-INT6-7
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NX drives, internal fan, frame size 6-7, power 18.5 - 55 kW
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NX-FAN-INT8
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, internal fan, frame size 8, 75 - 110 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-SUP-FR08
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan power supply kit, frame size 8, power 75 - 110 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NX-FAN-SUP-FR09
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan power supply kit, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NXIP54FR4
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL HVAC/NXS IP21 to IP54 upgrade kits
Product description: IP54 enclosure upgrade kit for NXL HVAC/NXS size 4 (HVAC03-HVAC12, NXS0003-NXS0012)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXIP54FR5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL HVAC/NXS IP21 to IP54 upgrade kits
Product description: IP54 enclosure upgrade kit for NXL HVAC/NXS size 5 (HVAC16-HVAC31, NXS0016-NXS0031)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXIP54FR6
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL HVAC/NXS IP21 to IP54 upgrade kits
Product description: IP54 enclosure upgrade kit for NXL HVAC/NXS size 6 (HVAC38-HVAC61, NXS0038-NXS0061)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXLOPTAA
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 3 digital inputs, 1 relay (NO/NC), 1 digital output
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NXLPANC
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL Display panels
Product description: NXL standard 7-segment display
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NXLPANRS
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS PC connection tools and cables
Product description: NXL RS232 adapter (for PC connection)
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
NXOPTA1
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: standard NXS slot A board: 6 DI, 1 DO (open collector), 2 AI, 1 AO
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
NXOPTB2
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 2 relays (1 NO, 1 NO/NC), 1 thermistor
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXOPTB8
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 3 Pt100 input
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
NXOPTC2
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Fieldbus cards
Product description: Modbus/N2 (RS485)
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
NXOPTC3
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Fieldbus cards
Product description: Profibus DP
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXOPTC6
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Fieldbus cards
Product description: CANopen (slave)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXOPTC7
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Fieldbus cards
Product description: DeviceNet
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXOPTCJ
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Fieldbus cards
Product description: BACnet MS/TP (RS485)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
NXPANA
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXS Display panels
Product description: NXS standard alpha-numeric display
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
NXPANG
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXS Display panels
Product description: NXS special display for Cyrillic or Chinese letters
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
NXS-CONTROL-BOX
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Control Spares
Product description: Varnished control unit for NXS with enclosure
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no
OCC/UD/DC
Trend Occupancy detectors
The ceiling mounted OCC/U occupancy detector is specifically designed for use in open plan office environments.
Mounting place: ceiling
Monitors Occupancy over approximately 5m2 diameter floor space. Extendable coverage of up to 10 detectors per IQ input
Model: adjustable 1 direction
OCC/UDA/DC
Trend Occupancy detectors
The ceiling mounted OCC/U occupancy detector is specifically designed for use in open plan office environments.
Mounting place: ceiling
Monitors Occupancy over approximately 5m2 diameter floor space. Extendable coverage of up to 10 detectors per IQ input
Model: adjustable 2 directions
OPT-BT-MC02-5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Control Spares
Product description: 5 pieces of real time clock batteries
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
OPTB1
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 6 digital inputs/outputs (programmable)
HVAC400: yes
NXL HVAC: no
NXS: yes
HVAC232/402: no
OPTB2
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 1 Thermistor, 2x RO
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes
OPTB4
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 1 analog input (mA), 2 analog output (mA)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
OPTB5
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 3 relays (NO)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
OPTB9
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 1 relay, 5 Vac inputs (42..240 Vac)
HVAC400: yes
NXL HVAC: no
NXS: yes
HVAC232/402: no
OPTBF
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: 1 analog input (mA/V), 1 relay (NO), 1 digital output (open collector)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
OPTBH
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Input/output expander cards
Product description: Pt1000, Ni1000, KTY84x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: yes
OPTC4
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Fieldbus cards
Product description: LonWorks
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
OPTE9
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
Fieldbus cards
Product description: Modbus TCP, Ethernet/IP
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: yes
PART/EJ104164
Trend Leads
Product description: IQ220/ADL local supervisor adapter (25 way to RJ11)
PCW/METER
Trend Wireless Sensors and Status
The TW/.. wireless temperature sensors, PCW/.. wireless pulse counters, flexible wireless system for BMS temperature measurement and metering.
Output signal: Wireless
Battery life: >=5 years
PCB cards can be mounted in any TB/XX plant sensor
Model: Pulse counter
Mounting place: no
PCW/STATUS
Trend Wireless Sensors and Status
The TW/.. wireless temperature sensors, PCW/.. wireless pulse counters, flexible wireless system for BMS temperature measurement and metering.
Output signal: Wireless
Battery life: >=5 years
PCB cards can be mounted in any TB/XX plant sensor
Model: Status signal
Mounting place: no
PIL4/10
Trend Pressure, Current sensor, Liquid
High accuracy gauge pressure sensor for liquids in HVAC applications.
Kind of pressure: gauge
Pressure connection: G1/2 (BSP) male thread.
Electrical connection: M12 two part connector
Protection class: IP67
Housing material: medium is only in contact with the stainless steel housing and the ceramic chip making the sensor suitable for use with all normal cleaning materials.
Sensing method: piezoresistive
Media temp.: -25...125C
Media temp. limit: Steam pigtail, required if used on steam or water above 85 oC (typically drops from 200 oC to ambient from medium to sensor)
Medium: liquid/gaseous
Ambient temperature: ...85C
Output signal: 4..20mA
Pressure range: 0...10bar
Max. pressure: 25bar
PIL4/16
Trend Pressure, Current sensor, Liquid
High accuracy gauge pressure sensor for liquids in HVAC applications.
Kind of pressure: gauge
Pressure connection: G1/2 (BSP) male thread.
Electrical connection: M12 two part connector
Protection class: IP67
Housing material: medium is only in contact with the stainless steel housing and the ceramic chip making the sensor suitable for use with all normal cleaning materials.
Sensing method: piezoresistive
Media temp.: -25...125C
Media temp. limit: Steam pigtail, required if used on steam or water above 85 oC (typically drops from 200 oC to ambient from medium to sensor)
Medium: liquid/gaseous
Ambient temperature: ...85C
Output signal: 4..20mA
Pressure range: 0...16bar
Max. pressure: 40bar
PIL4/25
Trend Pressure, Current sensor, Liquid
High accuracy gauge pressure sensor for liquids in HVAC applications.
Kind of pressure: gauge
Pressure connection: G1/2 (BSP) male thread.
Electrical connection: M12 two part connector
Protection class: IP67
Housing material: medium is only in contact with the stainless steel housing and the ceramic chip making the sensor suitable for use with all normal cleaning materials.
Sensing method: piezoresistive
Media temp.: -25...125C
Media temp. limit: Steam pigtail, required if used on steam or water above 85 oC (typically drops from 200 oC to ambient from medium to sensor)
Medium: liquid/gaseous
Ambient temperature: ...85C
Output signal: 4..20mA
Pressure range: 0...25bar
Max. pressure: 62bar
PIL4/4
Trend Pressure, Current sensor, Liquid
High accuracy gauge pressure sensor for liquids in HVAC applications.
Kind of pressure: gauge
Pressure connection: G1/2 (BSP) male thread.
Electrical connection: M12 two part connector
Protection class: IP67
Housing material: medium is only in contact with the stainless steel housing and the ceramic chip making the sensor suitable for use with all normal cleaning materials.
Sensing method: piezoresistive
Media temp.: -25...125C
Media temp. limit: Steam pigtail, required if used on steam or water above 85 oC (typically drops from 200 oC to ambient from medium to sensor)
Medium: liquid/gaseous
Ambient temperature: ...85C
Output signal: 4..20mA
Pressure range: 0...4bar
Max. pressure: 10bar
PIL4/6
Trend Pressure, Current sensor, Liquid
High accuracy gauge pressure sensor for liquids in HVAC applications.
Kind of pressure: gauge
Pressure connection: G1/2 (BSP) male thread.
Electrical connection: M12 two part connector
Protection class: IP67
Housing material: medium is only in contact with the stainless steel housing and the ceramic chip making the sensor suitable for use with all normal cleaning materials.
Sensing method: piezoresistive
Media temp.: -25...125C
Media temp. limit: Steam pigtail, required if used on steam or water above 85 oC (typically drops from 200 oC to ambient from medium to sensor)
Medium: liquid/gaseous
Ambient temperature: ...85C
Output signal: 4..20mA
Pressure range: 0...6bar
Max. pressure: 15bar
PMK-EEM400
Trend Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D
Panel mounting kit for front door of cabinet
PSR230/24-1.3
Trend Power Supply Modules
The PSR 24 Vdc switch-mode power supplies can tolerate a wide range of supply voltage and are distinguished by their high efficiency, compact dimensions, low weight, and low heat dissipation. Available in 1.3 A, 2.5 A and 5 A DIN rail mounting packages, all units feature overvoltage and short circuit protection and interference suppression.
Wide input voltage range
Long voltage fail bridging time
Input surge protected
Adjustable output voltage for lead resistance compensation (not 1.3 A version)
Output protected against open or short circuit
Operates up to 50 oC without derating
Double screw terminals on output
Over voltage protection on output
Product description: 24 Vdc, 30W (1.3 A) switch-mode power supply
PSR230/24-2.5
Trend Power Supply Modules
The PSR 24 Vdc switch-mode power supplies can tolerate a wide range of supply voltage and are distinguished by their high efficiency, compact dimensions, low weight, and low heat dissipation. Available in 1.3 A, 2.5 A and 5 A DIN rail mounting packages, all units feature overvoltage and short circuit protection and interference suppression.
Wide input voltage range
Long voltage fail bridging time
Input surge protected
Adjustable output voltage for lead resistance compensation (not 1.3 A version)
Output protected against open or short circuit
Operates up to 50 oC without derating
Double screw terminals on output
Over voltage protection on output
Product description: 24 Vdc, 60W (2.5 A) switch-mode power supply
PSR230/24-5.0
Trend Power Supply Modules
The PSR 24 Vdc switch-mode power supplies can tolerate a wide range of supply voltage and are distinguished by their high efficiency, compact dimensions, low weight, and low heat dissipation. Available in 1.3 A, 2.5 A and 5 A DIN rail mounting packages, all units feature overvoltage and short circuit protection and interference suppression.
Wide input voltage range
Long voltage fail bridging time
Input surge protected
Adjustable output voltage for lead resistance compensation (not 1.3 A version)
Output protected against open or short circuit
Operates up to 50 oC without derating
Double screw terminals on output
Over voltage protection on output
Product description: 24 Vdc, 120W (5 A) switch-mode power supply
PW20
Trend M-bus converter, PW
The PW Series are RS232/M-Bus converters which act as master interfaces for M-Bus networks with 3/20/60 slaves. They also have a ZVEI port for optical isolation. They are of a compact design (wall or DIN rail mounting) and have a broad supply voltage band.
Features include:
Communications speed from 300 to 9600 baud
Short circuit and over-voltage proof
Operating state indicated by LED on front of unit
Product description: Converter for max 20 M-bus derived units
PW3
Trend M-bus converter, PW
The PW Series are RS232/M-Bus converters which act as master interfaces for M-Bus networks with 3/20/60 slaves. They also have a ZVEI port for optical isolation. They are of a compact design (wall or DIN rail mounting) and have a broad supply voltage band.
Features include:
Communications speed from 300 to 9600 baud
Short circuit and over-voltage proof
Operating state indicated by LED on front of unit
Product description: Converter for max 3 M-bus derived units
PW60
Trend M-bus converter, PW
The PW Series are RS232/M-Bus converters which act as master interfaces for M-Bus networks with 3/20/60 slaves. They also have a ZVEI port for optical isolation. They are of a compact design (wall or DIN rail mounting) and have a broad supply voltage band.
Features include:
Communications speed from 300 to 9600 baud
Short circuit and over-voltage proof
Operating state indicated by LED on front of unit
Product description: Converter for max 60 M-bus derived units
RD-WMB-T
Trend Wallbus Room Display Units
The RD-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RD-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, monochrome, LCD display.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit LCD display with fan speed, occupancy, temperature, humidity, and setpoint displays
Setpoint, fan speed, and occupancy override controls
Display of CO2 and Outside Air Temperature values from the controller
Temperature sensing with humidity and CO2 options
Temperature and humidity versions also output dew point
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
Adjustments configurable with out of box default
Setpoint device: digital
Override button: digital
Fan switch: configurable
Room Display for use with controllers (Wallbus enabled). It has local sensor
RD-WMB-TC
Trend Wallbus Room Display Units
The RD-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RD-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, monochrome, LCD display.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit LCD display with fan speed, occupancy, temperature, humidity, and setpoint displays
Setpoint, fan speed, and occupancy override controls
Display of CO2 and Outside Air Temperature values from the controller
Temperature sensing with humidity and CO2 options
Temperature and humidity versions also output dew point
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
Adjustments configurable with out of box default
Setpoint device: digital
Override button: digital
Fan switch: configurable
Room Display for use with controllers (Wallbus enabled). It has local temperature, humidity and CO2 sensors and can give a dew point output.
RD-WMB-TH
Trend Wallbus Room Display Units
The RD-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RD-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, monochrome, LCD display.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit LCD display with fan speed, occupancy, temperature, humidity, and setpoint displays
Setpoint, fan speed, and occupancy override controls
Display of CO2 and Outside Air Temperature values from the controller
Temperature sensing with humidity and CO2 options
Temperature and humidity versions also output dew point
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
Adjustments configurable with out of box default
Setpoint device: digital
Override button: digital
Fan switch: configurable
Room Display for use with controllers (Wallbus enabled). It has local temperature sensor, local humidity sensor, and dew point output.
RD-WMB-THC
Trend Wallbus Room Display Units
The RD-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RD-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, monochrome, LCD display.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit LCD display with fan speed, occupancy, temperature, humidity, and setpoint displays
Setpoint, fan speed, and occupancy override controls
Display of CO2 and Outside Air Temperature values from the controller
Temperature sensing with humidity and CO2 options
Temperature and humidity versions also output dew point
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
Adjustments configurable with out of box default
Setpoint device: digital
Override button: digital
Fan switch: configurable
Room Display for use with controllers (Wallbus enabled). It has local temperature, humidity and CO2 sensors and can give a dew point output.
RD/SDU - ADAPTOR IQ1XX
Trend IQView4 Local Touch Screen Display
Accessories
RJ11 socket to 5 in line socket plus 2 way 24 V AUX adapter cable to connect to some IQ1xx controllers local supervisor ports, (use in conjunction with RD/SDUCOMMSCABLE/3M)
RD/SDU - ADAPTOR IQ1XX+
Trend IQView4 Local Touch Screen Display
Accessories
RJ11 socket to 25 way D type male plus 2 way 24 V AUX adaptor cable to connect to some IQ1xx controllers local supervisor ports, (use in conjunction with RD/SDUCOMMSCABLE/ 3M)
RD/SDU - ADAPTOR IQ2XX
Trend Wireless Receiver
Accessories
Adaptor cable for connecting XW/R/IQ to IQ251 and other earlier IQ2xx controllers which do not have 24 Vdc supplied via the RJ11 local supervisor port
RD/SDU - IQ2 COMMS CABLE 10M
Trend Leads
Product description: IQ2xx or IQ3xx to RD/SDU comms cable (10m length)
RD/SDU - IQ2 COMMS CABLE 3M
Trend Leads
Product description: IQ2xx or IQ3xx to RD/SDU comms cable (3m length)
RD/SDU-COMMSCABLE/3M
Trend IQView4 Local Touch Screen Display
Accessories
RJ11 plug to RJ11 plug to connect to IQ3, IQ2xx, and some IQ1xx controllers' local supervisor ports
RET-NX-FAN-8-SET
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan retrofit kit, (main fan, power supply), frame size 8, power 75 - 110 kW, SN -13068696, Date: 2012-10-05
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
RET-NX-FAN-9-SET
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NX Cooling Fans
Product description: NXS drives, fan retrofit kit, (main fan, power supply), frame size 9, power 132 - 160 kW, SN -13068696, Date: 2012-10-05
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no
RFI-0012-5-IP54
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 4
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
RFI-0031-5-IP54
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 5
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
RFI-0061-5-IP54
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 6
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
RFI-0105-5-IP54
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 7
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no
RP7517B1008
Trend Electro-Pneumatic converter
Input signal: electrical input 2..10 Vdc
Output signal: pressure output 20..100 kPa, proportional to input signal
Pressure connection: for 4 or 6 mm PE hose
Wiring connection: with 1 metre cable
Mounting: DIN rail
Air capacity 720 Nl/h.
Power supply: 24Vac
Max. pressure: 200kPa
Media temp.: 5...55C
RS-WMB-T
Trend Wallbus Room Sensor Units
The RS-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RS-WMB provides temperature, humidity, CO2 and dew point data from room/space to controllers via the Wallbus protocol. The housing is UV stable ABS and the subtle, clean design of the WMB family provides a balanced and unobtrusive aesthetic allowing the unit to complement but not detract from interior design themes.
Temperature range: 0...50C
R.H. range: 0...90%rh
Power and data on two wire, polarity independant Wallbus protocol, reducing wiring and increasing system reliability.
Temperature sensing plus humidity and CO2 options. and dew point output.
Humidity option also provides a dew point output.
Fully interchangeable with RD-WMB units to provide easy upgrade from sense only to sense, adjustment and display.
Protection class: IP 30
Mounting place: internal wall
Room Sensor - Temperature
RS-WMB-TC
Trend Wallbus Room Sensor Units
The RS-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RS-WMB provides temperature, humidity, CO2 and dew point data from room/space to controllers via the Wallbus protocol. The housing is UV stable ABS and the subtle, clean design of the WMB family provides a balanced and unobtrusive aesthetic allowing the unit to complement but not detract from interior design themes.
Temperature range: 0...50C
R.H. range: 0...90%rh
Power and data on two wire, polarity independant Wallbus protocol, reducing wiring and increasing system reliability.
Temperature sensing plus humidity and CO2 options. and dew point output.
Humidity option also provides a dew point output.
Fully interchangeable with RD-WMB units to provide easy upgrade from sense only to sense, adjustment and display.
Protection class: IP 30
Mounting place: internal wall
Room Sensor - Temperature and CO2
RS-WMB-TH
Trend Wallbus Room Sensor Units
The RS-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RS-WMB provides temperature, humidity, CO2 and dew point data from room/space to controllers via the Wallbus protocol. The housing is UV stable ABS and the subtle, clean design of the WMB family provides a balanced and unobtrusive aesthetic allowing the unit to complement but not detract from interior design themes.
Temperature range: 0...50C
R.H. range: 0...90%rh
Power and data on two wire, polarity independant Wallbus protocol, reducing wiring and increasing system reliability.
Temperature sensing plus humidity and CO2 options. and dew point output.
Humidity option also provides a dew point output.
Fully interchangeable with RD-WMB units to provide easy upgrade from sense only to sense, adjustment and display.
Protection class: IP 30
Mounting place: internal wall
Room Sensor - Temperature and Humidity
RS-WMB-THC
Trend Wallbus Room Sensor Units
The RS-WMB is part of the Wallbus room module family, pictured left, which has been designed to satisfy requirements at all stages of the contractual chain. The family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate.
The RS-WMB provides temperature, humidity, CO2 and dew point data from room/space to controllers via the Wallbus protocol. The housing is UV stable ABS and the subtle, clean design of the WMB family provides a balanced and unobtrusive aesthetic allowing the unit to complement but not detract from interior design themes.
Temperature range: 0...50C
R.H. range: 0...90%rh
Power and data on two wire, polarity independant Wallbus protocol, reducing wiring and increasing system reliability.
Temperature sensing plus humidity and CO2 options. and dew point output.
Humidity option also provides a dew point output.
Fully interchangeable with RD-WMB units to provide easy upgrade from sense only to sense, adjustment and display.
Protection class: IP 30
Mounting place: internal wall
Room Sensor - Temperature,Humidity and CO2
RS232C-4M
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS PC connection tools and cables
Product description: 4 m RS232 cable
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
RS232C2M
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS PC connection tools and cables
Product description: 2 m RS232 cable
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no
RV-BW-A
Trend Wallbus Room View Display Units
The RD-WMB is part of the Wallbus room module family and is designed to satisfy requirements at all stages of the contractual chain. The full colour touch screen display provides a clear, intuitive user interface and can be modified through the settings menu to show different home screen options and colours. The wallbus family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate. The RV-WMB is also available in a bezel-free option which, in conjunction with the pack of seperate bezels with adhesive mask (RV-BW-A)allows for additional late customization.
The RV-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, full colour, touch screen display. The settings menu provides a range of optional icons so that the user interface can be modified for systems requiring simple control of various room elements (lights, blinds, windows, heating etc...). There is also a backlight off option which allows the unit to be used where low lighting conditions are important.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit full colour display with fan speed, occupancy, temperature, humidity and setpoint displays
Setpoint, fan speed, and occupancy override controls
Temperature and humidity sensors with dew point output
Display of CO2 and Outside Air Temperature values from the controller
Red, Amber, Green indicator for CO2 levels
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
As well as setpoint adjustment the homescreen can display up to four icons form the settings menu. These can include lights, blinds, heating and windows.
Backlight off option for applications where low light levels are required.
Backdrop colour options to comply with project colour themes.
Setpoint device: no
Override button: no
Fan switch: no
Product description: Pack of 5
RV-WMB-TH
Trend Wallbus Room View Display Units
The RD-WMB is part of the Wallbus room module family and is designed to satisfy requirements at all stages of the contractual chain. The full colour touch screen display provides a clear, intuitive user interface and can be modified through the settings menu to show different home screen options and colours. The wallbus family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate. The RV-WMB is also available in a bezel-free option which, in conjunction with the pack of seperate bezels with adhesive mask (RV-BW-A)allows for additional late customization.
The RV-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, full colour, touch screen display. The settings menu provides a range of optional icons so that the user interface can be modified for systems requiring simple control of various room elements (lights, blinds, windows, heating etc...). There is also a backlight off option which allows the unit to be used where low lighting conditions are important.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit full colour display with fan speed, occupancy, temperature, humidity and setpoint displays
Setpoint, fan speed, and occupancy override controls
Temperature and humidity sensors with dew point output
Display of CO2 and Outside Air Temperature values from the controller
Red, Amber, Green indicator for CO2 levels
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
As well as setpoint adjustment the homescreen can display up to four icons form the settings menu. These can include lights, blinds, heating and windows.
Backlight off option for applications where low light levels are required.
Backdrop colour options to comply with project colour themes.
Setpoint device: digital
Override button: digital
Fan switch: configurable
Product description: Single Unit
RV-WMB-TH-BX
Trend Wallbus Room View Display Units
The RD-WMB is part of the Wallbus room module family and is designed to satisfy requirements at all stages of the contractual chain. The full colour touch screen display provides a clear, intuitive user interface and can be modified through the settings menu to show different home screen options and colours. The wallbus family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate. The RV-WMB is also available in a bezel-free option which, in conjunction with the pack of seperate bezels with adhesive mask (RV-BW-A)allows for additional late customization.
The RV-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, full colour, touch screen display. The settings menu provides a range of optional icons so that the user interface can be modified for systems requiring simple control of various room elements (lights, blinds, windows, heating etc...). There is also a backlight off option which allows the unit to be used where low lighting conditions are important.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit full colour display with fan speed, occupancy, temperature, humidity and setpoint displays
Setpoint, fan speed, and occupancy override controls
Temperature and humidity sensors with dew point output
Display of CO2 and Outside Air Temperature values from the controller
Red, Amber, Green indicator for CO2 levels
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
As well as setpoint adjustment the homescreen can display up to four icons form the settings menu. These can include lights, blinds, heating and windows.
Backlight off option for applications where low light levels are required.
Backdrop colour options to comply with project colour themes.
Setpoint device: digital
Override button: digital
Fan switch: configurable
Product description: Single Unit
RV-WMB-TH-KIT-10
Trend Wallbus Room View Display Units
The RD-WMB is part of the Wallbus room module family and is designed to satisfy requirements at all stages of the contractual chain. The full colour touch screen display provides a clear, intuitive user interface and can be modified through the settings menu to show different home screen options and colours. The wallbus family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate. The RV-WMB is also available in a bezel-free option which, in conjunction with the pack of seperate bezels with adhesive mask (RV-BW-A)allows for additional late customization.
The RV-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, full colour, touch screen display. The settings menu provides a range of optional icons so that the user interface can be modified for systems requiring simple control of various room elements (lights, blinds, windows, heating etc...). There is also a backlight off option which allows the unit to be used where low lighting conditions are important.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit full colour display with fan speed, occupancy, temperature, humidity and setpoint displays
Setpoint, fan speed, and occupancy override controls
Temperature and humidity sensors with dew point output
Display of CO2 and Outside Air Temperature values from the controller
Red, Amber, Green indicator for CO2 levels
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
As well as setpoint adjustment the homescreen can display up to four icons form the settings menu. These can include lights, blinds, heating and windows.
Backlight off option for applications where low light levels are required.
Backdrop colour options to comply with project colour themes.
Setpoint device: digital
Override button: digital
Fan switch: configurable
Product description: Pack of 10
RV-WMB-TH-KIT-BX-10
Trend Wallbus Room View Display Units
The RD-WMB is part of the Wallbus room module family and is designed to satisfy requirements at all stages of the contractual chain. The full colour touch screen display provides a clear, intuitive user interface and can be modified through the settings menu to show different home screen options and colours. The wallbus family has features that will appeal to architects, consultants, installation engineers, commissioning engineers, facility managers and building occupants. All units in the Wallbus family are fully interchangeable allowing room/space specifications to be changed by simply changing the front plate. The RV-WMB is also available in a bezel-free option which, in conjunction with the pack of seperate bezels with adhesive mask (RV-BW-A)allows for additional late customization.
The RV-WMB allows occupants to adjust fan speed, setpoint (graphical or numerical)and occupancy status and also to read assosciated values on a backlit, full colour, touch screen display. The settings menu provides a range of optional icons so that the user interface can be modified for systems requiring simple control of various room elements (lights, blinds, windows, heating etc...). There is also a backlight off option which allows the unit to be used where low lighting conditions are important.
Protection class: IP30
Mounting place: internal wall
Temperature range: 0...50C
R.H. range: 0...90%rh
Single power/signal connection to controller reduces wiring
Backlit full colour display with fan speed, occupancy, temperature, humidity and setpoint displays
Setpoint, fan speed, and occupancy override controls
Temperature and humidity sensors with dew point output
Display of CO2 and Outside Air Temperature values from the controller
Red, Amber, Green indicator for CO2 levels
Celsius or Fahrenheit display
Icon indication of fan speed and occupancy states
Digital display of local temperature or setpoint
As well as setpoint adjustment the homescreen can display up to four icons form the settings menu. These can include lights, blinds, heating and windows.
Backlight off option for applications where low light levels are required.
Backdrop colour options to comply with project colour themes.
Setpoint device: digital
Override button: digital
Fan switch: configurable
Product description: Pack of 10
S03010
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: no
Position feedback: 0..10V=
Runtime: 90s
Torque: 3Nm
Damper area: 0.6m2
S03010-SW1
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 1
Position feedback: 0..10V=
Runtime: 90s
Torque: 3Nm
Damper area: 0.6m2
S03230-2POS
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2
S03230-2POS-SW1
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2
S0324-2POS
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2
S0324-2POS-SW1
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2
S05010
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: no
Position feedback: 0..10V=
Runtime: 90s
Torque: 5Nm
Damper area: 1m2
S05010-SW1
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 1
Position feedback: 0..10V=
Runtime: 90s
Torque: 5Nm
Damper area: 1m2
S05230-2POS
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2
S05230-2POS-SW1
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2
S0524-2POS
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2
S0524-2POS-SW1
Trend Damper actuator 3/5 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2
S10010
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: optional
Position feedback: 0..10V=
Runtime: 90s
Torque: 10Nm
Damper area: 1.5m2
S10010-SW2
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 2
Position feedback: 0..10V=
Runtime: 90s
Torque: 10Nm
Damper area: 1.5m2
S10230-2POS
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2
S10230-2POS-SW2
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2
S1024-2POS
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2
S1024-2POS-SW2
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2
S20010
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: optional
Position feedback: 0..10V=
Runtime: 90s
Torque: 20Nm
Damper area: 4.6m2
S20010-SW2
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 2
Position feedback: 0..10V=
Runtime: 90s
Torque: 20Nm
Damper area: 4.6m2
S20230-2POS
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2
S20230-2POS-SW2
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2
S2024-2POS
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2
S2024-2POS-SW2
Trend Damper actuator 10/20 Nm, SmartAct springreturn
Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s
Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2
SIN-0010-5-0-P
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 10 A (40oC), 8,8 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
SIN-0018-5-0-P
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 18 A (40oC), 16 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
SIN-0032-5-0-P
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 32 A (40oC), 28 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
SIN-0048-5-0-P
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 48 A (40oC), 42 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
SIN-0075-5-0-P
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 75 A (40oC), 66 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
SIN-0110-5-0-P
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 110 A (40oC), 97 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
SIN-0180-5-0-P
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 180 A (40oC), 155 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no
SL-361/P
Trend Wireless Sensors and Status
The TW/.. wireless temperature sensors, PCW/.. wireless pulse counters, flexible wireless system for BMS temperature measurement and metering.
Output signal: Wireless
Battery life: >=5 years
PCB cards can be mounted in any TB/XX plant sensor
Model: Replacement battery for TW/S and TW/P
Mounting place: no
SMARTDRIVE-USBC
Trend Parts and accessories for inverters
Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.
SmartDrive PC connection tools and cables
Product description: SmartDrive 3.0m USB PC connection cable
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: yes
SOFTWARE RELICENSE
Trend 963 Supervisor
Upgrades
963 Re-license of product over 3 yrs old
SRMAC
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: Single Relay Module; 24 Vac (triac) output signal to a 10 A relay output
SRMV
Trend Input and Output Modules
Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.
Output Modules
Product description: Single Relay Module; 10 Vdc analogue output signal to a 8 A relay output
SW2
Trend Damper actuator 20/34 Nm, SmartAct
Optional accessories
End switch kit, with 2 SPDT freely adjustable end-switches
T/AV-L
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...110C
Temperature element: Pt100 averaging
Mounting place: air duct
Immersion depth: 7000mm
Cable length: no
T/AV-S
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...110C
Temperature element: Pt100 averaging
Mounting place: air duct
Immersion depth: 3500mm
Cable length: no
T/FGL
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: 0...400C
Temperature element: Pt100
Mounting place: flue gas vent
Immersion depth: 380mm
Cable length: no
T/FGS
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: 0...400C
Temperature element: Pt100
Mounting place: flue gas vent
Immersion depth: 230mm
Cable length: no
T/PC/-40
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -40...50C
Temperature element: Pt100
Mounting place: strap on pipe
Immersion depth: no
Cable length: 2m
T/PC/110
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...110C
Temperature element: Pt100
Mounting place: strap on pipe
Immersion depth: no
Cable length: 2m
T/PC/160
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...160C
Temperature element: Pt100
Mounting place: strap on pipe
Immersion depth: no
Cable length: 2m
T/PC/40
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...40C
Temperature element: Pt100
Mounting place: strap on pipe
Immersion depth: no
Cable length: 2m
T/PI-L/40
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...40C
Temperature element: Pt100
Mounting place: air duct
Immersion depth: 400mm
Cable length: no
T/PI-S/-40
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -40...50C
Temperature element: Pt100
Mounting place: in well
Immersion depth: 150mm
Cable length: no
T/PI-S/110
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...110C
Temperature element: Pt100
Mounting place: in well
Immersion depth: 150mm
Cable length: no
T/PI-S/40
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...40C
Temperature element: Pt100
Mounting place: duct + well
Immersion depth: 150mm
Cable length: no
T/PI/160
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -10...160C
Temperature element: Pt100
Mounting place: in well
Immersion depth: 155mm
Cable length: no
T/PO/-40
Trend Plant Temperature Sensors (Pt100)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air, averaging and flue gas.
Output signal: 4..20mA
Protection class: IP67 Housing
Temperature range: -40...50C
Temperature element: Pt100
Mounting place: wall outside
Immersion depth: no
Cable length: no
T/PS
Trend Space Temperature Sensors (Pt100)
Pt100 space temperature sensor for the measurement of ambient temperature.
Temperature element: Pt100
Output signal: 4..20mA
Mounting place: internal wall
Temperature range: -10...40C
T/TFR-4/10
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -10...50C
Mounting place: inside unit
Immersion depth: no
Cable length: 4m
Packing unit quantity: 10
T/TS
Trend Space Temperature Sensors (NTC10k)
Thermistor space temperature sensors for the measurement of ambient temperature.
Temperature element: NTC10k
Protection class: T/TS (only) rugged space temperature sensor IP65
Mounting place: internal wall
IQ Override Button: no
Status LED: no
Temperature range: -10...40C
Setpoint Knob: no
IQL Override Button: no
Fan Auto/Off/ 1/2/3: no
Heat measurement: radiant
Housing: vandal proof
Packing unit quantity: 1
TB/TC
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -30...100C
Mounting place: strap on pipe
Immersion depth: no
Cable length: 2m
Packing unit quantity: 1
TB/TI-ES
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -30...110C
Mounting place: duct + well
Immersion depth: 50mm
Cable length: no
Packing unit quantity: 1
TB/TI-L
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -30...110C
Mounting place: air duct
Immersion depth: 400mm
Cable length: no
Packing unit quantity: 1
TB/TI-L/BOX12
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -30...110C
Mounting place: air duct
Immersion depth: 400mm
Cable length: no
Packing unit quantity: 1
TB/TI-S
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -30...110C
Mounting place: duct + well
Immersion depth: 150mm
Cable length: no
Packing unit quantity: 1
TB/TI-S/BOX12
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -30...110C
Mounting place: duct + well
Immersion depth: 150mm
Cable length: no
Packing unit quantity: 1
TB/TO
Trend Plant Temperature Sensors (NTC10k)
A range of temperature sensors comprising of immersion, duct, clamp-on, outside air and flying lead.
Temperature element: NTC10k
Protection class: IP67 Housing
Temperature range: -30...50C
Mounting place: wall outside
Immersion depth: no
Cable length: no
Packing unit quantity: 1
TB/TS
Trend Space Temperature Sensors (NTC10k)
Thermistor space temperature sensors for the measurement of ambient temperature.
Temperature element: NTC10k
Protection class: T/TS (only) rugged space temperature sensor IP65
Mounting place: internal wall
IQ Override Button: no
Status LED: no
Temperature range: 0...40C
Setpoint Knob: no
IQL Override Button: no
Fan Auto/Off/ 1/2/3: no
Heat measurement: convective
Housing: standard
Packing unit quantity: 1
TB/TS/BOX20
Trend Space Temperature Sensors (NTC10k)
Thermistor space temperature sensors for the measurement of ambient temperature.
Temperature element: NTC10k
Protection class: T/TS (only) rugged space temperature sensor IP65
Mounting place: internal wall
IQ Override Button: no
Status LED: no
Temperature range: 0...40C
Setpoint Knob: no
IQL Override Button: no
Fan Auto/Off/ 1/2/3: no
Heat measurement: convective
Housing: standard
Packing unit quantity: 20
TB/TS/K
Trend Space Temperature Sensors (NTC10k)
Thermistor space temperature sensors for the measurement of ambient temperature.
Temperature element: NTC10k
Protection class: T/TS (only) rugged space temperature sensor IP65
Mounting place: internal wall
IQ Override Button: no
Status LED: no
Temperature range: 0...40C
Setpoint Knob: yes
IQL Override Button: no
Fan Auto/Off/ 1/2/3: no
Heat measurement: convective
Housing: standard
Packing unit quantity: 1
TB/TS/K/BOX20
Trend Space Temperature Sensors (NTC10k)
Thermistor space temperature sensors for the measurement of ambient temperature.
Temperature element: NTC10k
Protection class: T/TS (only) rugged space temperature sensor IP65
Mounting place: internal wall
IQ Override Button: no
Status LED: no
Temperature range: 0...40C
Setpoint Knob: yes
IQL Override Button: no
Fan Auto/Off/ 1/2/3: no
Heat measurement: convective
Housing: standard
Packing unit quantity: 20
TB/TS/KEF
Trend IQeco31 controller 24V version
Accessories
Similar to TB/TS/KO plus fan speed control switch.
TB/TS/KEF/BOX20
Trend Space Temperature Sensors (NTC10k)
Thermistor space temperature sensors for the measurement of ambient temperature.
Temperature element: NTC10k
Protection class: T/TS (only) rugged space temperature sensor IP65
Mounting place: internal wall
IQ Override Button: no
Status LED: no
Temperature range: 0...40C
Setpoint Knob: yes
IQL Override Button: yes
Fan Auto/Off/ 1/2/3: yes
Heat measurement: convective
Housing: standard
Packing unit quantity: 20
TB/TS/KO
Trend IQeco31 controller 24V version
Accessories
As TB/TS/K plus occupation override push button.
TB/TS/KOS
Trend IQeco31 controller 24V version
Accessories
As TB/TS/KO plus occupation status LEDs.
TB/TS/KOSF
Trend IQeco31 controller 24V version
Accessories
As TB/TS/KOS plus fan speed control switch.
TEM/TU/050
Trend Trend Energy Manager
Trend Energy Manager (TEM) is a web-based energy performance monitoring, reporting and analysis tool. The system collects, stores and analyses energy data that is retrieved from the Trend Building Energy Management System (BEMS). Connection can be made over TCP/IP or autodialled (e.g. Trend Modem Node (TMN), ADL, SANC) links. Any data point (sensor/meter) that is being logged synchronously within a Trend controller can be accessed and monitored using Trend Energy Manager. These could include data points such as Space Temperature Sensors, Outside Air Temperature Sensors, boiler and chiller flow sensors, and main utility meters and sub-meters (electric, gas and water). Data collection and storage can be incorporated into an existing network server, or a dedicated server can be used. Data collection is achieved using the Data Collector, with data being stored in the SQL Server 2008 R2 Express Edition database, both provided as part of the TEM package. Data collection and data point setup can be performed by a Trend qualified engineer. (Full training can be provided by Trend). From the data that is generated and displayed, in graphical and tabular formats, operating patterns and energy wastage areas can easily be identified.
Features include:
Web-based energy monitoring tool
Collects, stores and analyses data retrieved on-site
Any data point set up for synchronised plots can be accessed and monitored via Trend controller(s)
Up to 500 data points can be monitored and up to 10 concurrent users can access the TEM system, depending on the level of licence obtained
Displays data in graphical and tabular formats so that operating patterns and energy wastage areas can easily be identified
Graph zoom in and out feature, in order to quickly and easily break down the data that is to be viewed
Enables analysis of energy consumption data and finding trends in energy performance
Generates reports for the purposes of monitoring energy usage and costs
Comparisons can be made with current data against historical data (targeting), and against profiles which have been set up for expected consumption, based on the historical data
Degree day calculation performed by Trend system using OAT sensor readings, or calculated in Trend controller and relayed to the TEM system
Data Collector tool and SQL Server 2008 R2 Express database provided as part of package; all in one easy installation
Product description: Trend Energy Manager for 50 data points (3 users)
TEM/TU/100
Trend Trend Energy Manager
Trend Energy Manager (TEM) is a web-based energy performance monitoring, reporting and analysis tool. The system collects, stores and analyses energy data that is retrieved from the Trend Building Energy Management System (BEMS). Connection can be made over TCP/IP or autodialled (e.g. Trend Modem Node (TMN), ADL, SANC) links. Any data point (sensor/meter) that is being logged synchronously within a Trend controller can be accessed and monitored using Trend Energy Manager. These could include data points such as Space Temperature Sensors, Outside Air Temperature Sensors, boiler and chiller flow sensors, and main utility meters and sub-meters (electric, gas and water). Data collection and storage can be incorporated into an existing network server, or a dedicated server can be used. Data collection is achieved using the Data Collector, with data being stored in the SQL Server 2008 R2 Express Edition database, both provided as part of the TEM package. Data collection and data point setup can be performed by a Trend qualified engineer. (Full training can be provided by Trend). From the data that is generated and displayed, in graphical and tabular formats, operating patterns and energy wastage areas can easily be identified.
Features include:
Web-based energy monitoring tool
Collects, stores and analyses data retrieved on-site
Any data point set up for synchronised plots can be accessed and monitored via Trend controller(s)
Up to 500 data points can be monitored and up to 10 concurrent users can access the TEM system, depending on the level of licence obtained
Displays data in graphical and tabular formats so that operating patterns and energy wastage areas can easily be identified
Graph zoom in and out feature, in order to quickly and easily break down the data that is to be viewed
Enables analysis of energy consumption data and finding trends in energy performance
Generates reports for the purposes of monitoring energy usage and costs
Comparisons can be made with current data against historical data (targeting), and against profiles which have been set up for expected consumption, based on the historical data
Degree day calculation performed by Trend system using OAT sensor readings, or calculated in Trend controller and relayed to the TEM system
Data Collector tool and SQL Server 2008 R2 Express database provided as part of package; all in one easy installation
Product description: Trend Energy Manager for 100 data points (5 users)
TEM/TU/250
Trend Trend Energy Manager
Trend Energy Manager (TEM) is a web-based energy performance monitoring, reporting and analysis tool. The system collects, stores and analyses energy data that is retrieved from the Trend Building Energy Management System (BEMS). Connection can be made over TCP/IP or autodialled (e.g. Trend Modem Node (TMN), ADL, SANC) links. Any data point (sensor/meter) that is being logged synchronously within a Trend controller can be accessed and monitored using Trend Energy Manager. These could include data points such as Space Temperature Sensors, Outside Air Temperature Sensors, boiler and chiller flow sensors, and main utility meters and sub-meters (electric, gas and water). Data collection and storage can be incorporated into an existing network server, or a dedicated server can be used. Data collection is achieved using the Data Collector, with data being stored in the SQL Server 2008 R2 Express Edition database, both provided as part of the TEM package. Data collection and data point setup can be performed by a Trend qualified engineer. (Full training can be provided by Trend). From the data that is generated and displayed, in graphical and tabular formats, operating patterns and energy wastage areas can easily be identified.
Features include:
Web-based energy monitoring tool
Collects, stores and analyses data retrieved on-site
Any data point set up for synchronised plots can be accessed and monitored via Trend controller(s)
Up to 500 data points can be monitored and up to 10 concurrent users can access the TEM system, depending on the level of licence obtained
Displays data in graphical and tabular formats so that operating patterns and energy wastage areas can easily be identified
Graph zoom in and out feature, in order to quickly and easily break down the data that is to be viewed
Enables analysis of energy consumption data and finding trends in energy performance
Generates reports for the purposes of monitoring energy usage and costs
Comparisons can be made with current data against historical data (targeting), and against profiles which have been set up for expected consumption, based on the historical data
Degree day calculation performed by Trend system using OAT sensor readings, or calculated in Trend controller and relayed to the TEM system
Data Collector tool and SQL Server 2008 R2 Express database provided as part of package; all in one easy installation
Product description: Trend Energy Manager for 250 data points (5 users)
TEM/TU/500
Trend Trend Energy Manager
Trend Energy Manager (TEM) is a web-based energy performance monitoring, reporting and analysis tool. The system collects, stores and analyses energy data that is retrieved from the Trend Building Energy Management System (BEMS). Connection can be made over TCP/IP or autodialled (e.g. Trend Modem Node (TMN), ADL, SANC) links. Any data point (sensor/meter) that is being logged synchronously within a Trend controller can be accessed and monitored using Trend Energy Manager. These could include data points such as Space Temperature Sensors, Outside Air Temperature Sensors, boiler and chiller flow sensors, and main utility meters and sub-meters (electric, gas and water). Data collection and storage can be incorporated into an existing network server, or a dedicated server can be used. Data collection is achieved using the Data Collector, with data being stored in the SQL Server 2008 R2 Express Edition database, both provided as part of the TEM package. Data collection and data point setup can be performed by a Trend qualified engineer. (Full training can be provided by Trend). From the data that is generated and displayed, in graphical and tabular formats, operating patterns and energy wastage areas can easily be identified.
Features include:
Web-based energy monitoring tool
Collects, stores and analyses data retrieved on-site
Any data point set up for synchronised plots can be accessed and monitored via Trend controller(s)
Up to 500 data points can be monitored and up to 10 concurrent users can access the TEM system, depending on the level of licence obtained
Displays data in graphical and tabular formats so that operating patterns and energy wastage areas can easily be identified
Graph zoom in and out feature, in order to quickly and easily break down the data that is to be viewed
Enables analysis of energy consumption data and finding trends in energy performance
Generates reports for the purposes of monitoring energy usage and costs
Comparisons can be made with current data against historical data (targeting), and against profiles which have been set up for expected consumption, based on the historical data
Degree day calculation performed by Trend system using OAT sensor readings, or calculated in Trend controller and relayed to the TEM system
Data Collector tool and SQL Server 2008 R2 Express database provided as part of package; all in one easy installation
Product description: Trend Energy Manager for 500 data points (10 users)
TEM/TU/UP /050/100
Trend Trend Energy Manager
Upgrades
Trend Energy Manager upgrade 50 data points (3 user) to 100 data points (5 users)
TEM/TU/UP /100/250
Trend Trend Energy Manager
Upgrades
Trend Energy Manager upgrade 100 data points (5 user) to 250 data points (5 users)
TEM/TU/UP /250/500
Trend Trend Energy Manager
Upgrades
Trend Energy Manager upgrade 250 data points (5 user) to 500 data points (10 users)
TMNG/EUR
Trend Trend Modem Node Controller (TMN...)
The TMN range allows either networked or stand-alone IQ System devices to access the Public Switched Telephone Network (PSTN) via an integral or external modem, or to access the Integrated Services Digital Network (ISDN) via a terminal adaptor. The TMNG uses wireless communication via a GSM service provider enabling connections to sites without landlines and direct SMS messaging (text messages) to mobile phones. The TMN can communicate either to single or multiple devices over the IQ system current loop Lan. It also supports text messaging and communications to radiopagers via the PSTN and is supplied either boxed, or as a board which can be fitted in other IQ system devices (e.g. IQ controllers). There are high speed integral modem, GSM modem, and external modem/terminal adaptor versions.
Network: Trend LAN
Enables communication between IQ System devices over PSTN, ISDN, or GSM.
TMNG enables wireless communication and direct SMS messaging to mobile phones
Memory retains telephone numbers and settings on power fail without battery.
Can be used on IQ system current loop Lans and internetwork or direct connected to software tool or controller.
TMNH high speed integral modem has international approvals.
Fast data rate reduces transmission times.
TMNG (Trend Modem Node GSM)
Model: GSM modem
Power: 24Vdc
Comments: no
TMNH/UK
Trend Trend Modem Node Controller (TMN...)
The TMN range allows either networked or stand-alone IQ System devices to access the Public Switched Telephone Network (PSTN) via an integral or external modem, or to access the Integrated Services Digital Network (ISDN) via a terminal adaptor. The TMNG uses wireless communication via a GSM service provider enabling connections to sites without landlines and direct SMS messaging (text messages) to mobile phones. The TMN can communicate either to single or multiple devices over the IQ system current loop Lan. It also supports text messaging and communications to radiopagers via the PSTN and is supplied either boxed, or as a board which can be fitted in other IQ system devices (e.g. IQ controllers). There are high speed integral modem, GSM modem, and external modem/terminal adaptor versions.
Network: Trend LAN
Enables communication between IQ System devices over PSTN, ISDN, or GSM.
TMNG enables wireless communication and direct SMS messaging to mobile phones
Memory retains telephone numbers and settings on power fail without battery.
Can be used on IQ system current loop Lans and internetwork or direct connected to software tool or controller.
TMNH high speed integral modem has international approvals.
Fast data rate reduces transmission times.
TMNH (Trend Modem Node High speed)
Model: high speed integral modem
Power: 24Vdc
Comments: no
TONN-8-24
Trend Trend Open Network Node (TONN8)
Spare Parts
TONN8 Hardware only no WIFI - for Warranty/Repair only. License must be transferred from existing host
TONN-8-CLIP
Trend Trend Open Network Node (TONN8)
Spare Parts
Trend branded clip for TONN8
TONN-8-SD
Trend Trend Open Network Node (TONN8)
Spare Parts
SD Card for TONN8
TONN-8100-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with 100 Proxy Points license and 1 year software update agreement
TONN-810000-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with 10000 Proxy Points license and 1 year software update agreement
TONN-81250-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with 1250 Proxy Points license and 1 year software update agreement
TONN-8250-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with 250 Proxy Points license and 1 year software update agreement
TONN-8500-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with 500 Proxy Points license and 1 year software update agreement
TONN-85000-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with 5000 Proxy Points license and 1 year software update agreement
TONN-DEVICE-UP-10
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 upgrades
Product description: TONN8 Upgrade for an addition 500 proxy points
TONN-DEVICE-UP-25
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 upgrades
Product description: TONN8 Upgrade for an addition 1250 proxy points
TONN-DEVICE-UP-50
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 upgrades
Product description: TONN8 Upgrade for an addition 2500 proxy points
TONN-DR-MFID
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Additional Drivers
Product description: Fidelio Driver for N4 TONN8
TONN-DR-SMS-ALM
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Additional Drivers
Product description: SMS Driver for N4 TONN8
TONN-JACE-8000-AX
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Additional Drivers
Product description: Enables TONN8 to run Niagara AX
TONN-NXEM-232
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 expansion modules
Product description: TONN8 RS232 Expansion Module - Single Port
TONN-NXEM-2X485
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 expansion modules
Product description: TONN8 RS485 Expansion Module - Dual Port
TONN-NXEM-LON
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 expansion modules
Product description: TONN8 LON Expansion Module - Single Port
TONN-SMA-8005-1YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 1 year software update agreement for a 250-499 point TONN8
TONN-SMA-8005-3YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 3 year software update agreement for a 250-499 point TONN8
TONN-SMA-8005-5YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 5 year software update agreement for a 250-499 point TONN8
TONN-SMA-8010-1YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 1 year software update agreement for a 500-1249 point TONN8
TONN-SMA-8010-3YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 3 year software update agreement for a 500-1249 point TONN8
TONN-SMA-8010-5YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 5 year software update agreement for a 500-1249 point TONN8
TONN-SMA-8025-1YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 1 year software update agreement for a 1250-4999 point TONN8
TONN-SMA-8025-3YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 3 year software update agreement for a 1250-4999 point TONN8
TONN-SMA-8025-5YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 5 year software update agreement for a 1250-4999 point TONN8
TONN-SMA-8100-1YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 1 year software update agreement for a 5000-9999 point TONN8
TONN-SMA-8100-3YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 3 year software update agreement for a 5000-9999 point TONN8
TONN-SMA-8100-5YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 5 year software update agreement for a 5000-9999 point TONN8
TONN-SMA-8200-1YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 1 year software update agreement for a 10000+ point TONN8
TONN-SMA-8200-3YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 3 year software update agreement for a 10000+ point TONN8
TONN-SMA-8200-5YR
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
Licences
Product description: 5 year software update agreement for a 10000+ point TONN8
TONN-W02-8-24
Trend Trend Open Network Node (TONN8)
Spare Parts
TONN-8 Hardware only with WIFI module for zone 2 - for Warranty/Repair only. License must be transferred from existing host
TONN-W02-8100-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with WIFI module Zone 2, 100 Proxy Points license and 1 year software update agreement
TONN-W02-810000-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with WIFI module Zone 2, 10000 Proxy Points license and 1 year software update agreement
TONN-W02-81250-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with WIFI module Zone 2, 1250 Proxy Points license and 1 year software update agreement
TONN-W02-8250-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with WIFI module Zone 2, 250 Proxy Points license and 1 year software update agreement
TONN-W02-8500-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with WIFI module Zone 2, 500 Proxy Points license and 1 year software update agreement
TONN-W02-85000-24
Trend Trend Open Network Node (TONN8)
The TONN8 is a compact, embedded IoT (Internet of Things) controller and server platform for connecting multiple and diverse devices and sub-systems. It supports many OPEN protocols such as; BACnet, OBIX, LONWORKS, KNX, MODBUS, M-BUS and many more. In essence it can read and write data between the Trend system and many other Heating Ventilation & Air Conditioning (HVAC) and NONHVAC control systems (e.g. lighting). The TONN8 can read and write data from and to the 3rd party systems and make that data available to IQ controllers.
TONN also includes the following features:
Supplied with a Trend Driver as standard and comprehensive set of other drivers
Additional optional drivers available: Micros Fidelio hotel room booking system (IP) and the SMS driver.
Faster CPU & more memory.The TONN8 has a more powerful processor and greater memory capacity, making it faster and capable of tackling far more complex applications.
Improved Security.TONN8 delivers all the security you woud expect in a modern device with encrypted communication (FOXS, HTTPS)and Java-free access via Web-Browsers (HTML5) as standard.
DIN rail or surface mounting.
2 Ethernet ports and 2 x RS485 ports.
24 Vac power supply.
TONN8 (Trend Open Network Node)
Product description: TONN8 with WIFI module Zone 2, 5000 Proxy Points license and 1 year software update agreement
TONN/BAT
Trend Trend Open Network Node (TONN)
Battery replacement
Replacement battery pack with mounting frame for TONN2, TONN6, TONN6E.
TONN/DRIVER/AA _PHP/SER
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: American Automatrics PHP over RS232 or RS485
TONN/DRIVER/AA _PUP/SER
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: American Automatrics PUP over RS232 or RS485
TONN/DRIVER/FLEX/SER
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Flex Driver over RS232 or RS485
TONN/DRIVER/Fidelio/IP
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Micros Fidelio hotel room booking system driver (IP)
TONN/DRIVER/Global_Cache/IP
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Global Cache Driver
TONN/DRIVER/Helvar/SER
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Helvar serial driver
TONN/DRIVER/Horstmann/SER
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Horstmann serial Driver
TONN/DRIVER/Protec/SER
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Protec fire panel serial driver
TONN/DRIVER/Resol/SER
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Resol solar water heating controller serial driver
TONN/DRIVER/UP/ENHANCED
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
Additional Drivers
Product description: Upgrade to the Trend Enhanced driver
TONN/MEM/UP/230/240
Trend Trend Open Network Node (TONN)
Memory Upgrades
Upgrade of TONN 230 to 240
TONN/MEM/UP/240/250
Trend Trend Open Network Node (TONN)
Memory Upgrades
Upgrade of TONN 240 to 250
TONN/MEM/UP/330E/340E
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
TONN upgrades
Product description: Upgrade of TONN 340 to 350
TONN/MEM/UP/340E/350E
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
TONN upgrades
Product description: Upgrade of TONN 350 to 360
TONN/MEM/UP/650/660
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
TONN upgrades
Product description: Upgrade of TONN 650 to 660
TONN/MEM/UP/650E/660E
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
TONN upgrades
Product description: Upgrade of TONN 650E to 660E
TONN/MEM/UP/LATEST REVISION
Trend Trend Open Network Node (TONN)
The Trend Open Network Node (TONN) is a Trend network device that enables the Trend system to interface with 3rd party systems such as BACnet, LONWORKS, Mbus, MODBUS, SNMP, and KNX. It utilises the NiagaraAX Framework for the integration of Heating, Ventilation, Air Conditioning (HVAC) systems and non-HVAC systems (e.g. lighting) in a building. TONN reads the required data from the 3rd party systems, and makes it available to IQ3 controllers. Data from the controllers can be made available to the 3rd party systems to provide a single supervisory option. TONN enables values from the Trend system to be read and written by the 3rd party systems connected to the TONN, and for the Trend system to read values from and write values to the 3rd party systems.
TONN also includes the following features:
Supplied with drivers for BACnet IP, BACnet MSTP, EIB/KNX IP, LONFTT, LON IP, MODBUSRTU Master, MODBUSRTU Slave, MODBUSTCP Master, MODBUSTCP Slave, MBus Serial, MBus IP, oBIX, and SNMP systems.
Additional optional drivers available: Flex over RS232 or RS485, Micros Fidelio hotel room booking system (IP), Global Cache, Horstmann serial, Helvar serial, American Automatrics PHP over RS232 or RS485 and American Automatrics PUP over RS232 or RS485.
Read and write values from 3rd party systems.
Read and write Trend system values from/to 3rd party systems.
DIN rail or surface mounting.
2 Ethernet ports, 1 x RS232 port, and 1 x RS485 port.
Up to 2 optional plug in communications cards for RS232, LON FTT, and RS485.
15 Vdc power supply.
TONN upgrades
Product description: Upgrade to Latest Revision of TONN Firmware
TP/1/1/22/HF/200-600V
Trend Cables
Screened and unscreened twisted pair cables recommended for general purpose Trend system installations. All cables are manufactured with a violet, halogen-free outer sheath and are voltage rated at 600V. Screened cables have twisted pairs wrapped in an aluminium polyester tape with a tinned copper drain wire.
Model: Screened single twisted pair
Comments: Belden equivalent 8761NH, 200 metres, 600V rating.
TP/1/1/24/HF/305-600V
Trend Cables
Screened and unscreened twisted pair cables recommended for general purpose Trend system installations. All cables are manufactured with a violet, halogen-free outer sheath and are voltage rated at 600V. Screened cables have twisted pairs wrapped in an aluminium polyester tape with a tinned copper drain wire.
Model: Screened twin twisted pair
Comments: Belden equivalent 9841NH, 305 metres, 600V rating.
TP/1/1/24/HF/305/600V
Trend IQeco31 controller 24V version
Accessories
Screened twisted-pair cable for MSTP network 24 AWG 305 metre.
TP/2/2/22/HF/200-600V
Trend Cables
Screened and unscreened twisted pair cables recommended for general purpose Trend system installations. All cables are manufactured with a violet, halogen-free outer sheath and are voltage rated at 600V. Screened cables have twisted pairs wrapped in an aluminium polyester tape with a tinned copper drain wire.
Model: Screened twin twisted pair
Comments: Belden equivalent 8723NH, 200 metres, 600V rating.
TREND ENERGYEYE
Trend Trend EnergyEYE
Trend EnergyEYE is a local site software application that displays utility readings that are connected to the Trend Building & Energy Management System (BEMS). It can display meter readings from Electricity and Gas monitored by a 963 Supervisor head end and show yesterdays, last month and year to date values as well as a monthly graph in either a line or bar chart.
Shows any utility data connected to a Trend BEMS controller with a 963 supervisor
Tailored conversion factors for CO2
Configured targets with traffic light indication of current consumption
Scrolling text option
Display FLV movie files
Auto sizing application to screen connected to computer
Configurable background and layout
Runs as standalone application on networked Windows computer.
Product description: Trend EnergyEYE software on CD
TS/TS/BOX5
Trend Space Temperature Sensors (NTC10k)
Thermistor space temperature sensors for the measurement of ambient temperature.
Temperature element: NTC10k
Protection class: T/TS (only) rugged space temperature sensor IP65
Mounting place: internal wall
IQ Override Button: no
Status LED: no
Temperature range: 0...40C
Setpoint Knob: no
IQL Override Button: no
Fan Auto/Off/ 1/2/3: no
Heat measurement: convective
Housing: standard
Packing unit quantity: 5
TW/P
Trend Wireless Sensors and Status
The TW/.. wireless temperature sensors, PCW/.. wireless pulse counters, flexible wireless system for BMS temperature measurement and metering.
Output signal: Wireless
Battery life: >=5 years
PCB cards can be mounted in any TB/XX plant sensor
Model: Plant sensor PCB
Mounting place: no
TW/S
Trend Wireless Sensors and Status
The TW/.. wireless temperature sensors, PCW/.. wireless pulse counters, flexible wireless system for BMS temperature measurement and metering.
Output signal: Wireless
Battery life: >=5 years
PCB cards can be mounted in any TB/XX plant sensor
Model: Space sensor
Mounting place: internal wall
V5004TF1050
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve with actuator included, providing position feedback
DN size: 50mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 2000l/h
Maximum flow (qs): 20000l/h
Delta-P: 40...400kPa
V5004TF1065
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve with actuator included, providing position feedback
DN size: 65mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 3000l/h
Maximum flow (qs): 30000l/h
Delta-P: 30...400kPa
V5004TF1080
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve with actuator included, providing position feedback
DN size: 80mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 3000l/h
Maximum flow (qs): 30000l/h
Delta-P: 30...400kPa
V5004TF1100
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve with actuator included, providing position feedback
DN size: 100mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 5500l/h
Maximum flow (qs): 55000l/h
Delta-P: 30...400kPa
V5004TF1125
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve with actuator included, providing position feedback
DN size: 125mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 9000l/h
Maximum flow (qs): 90000l/h
Delta-P: 35...400kPa
V5004TF1150
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve with actuator included, providing position feedback
DN size: 150mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 15000l/h
Maximum flow (qs): 100000l/h
Delta-P: 50...400kPa
V5004TY10150150
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 2.9 mm
DN size: 15mm
Port connection: internal threads
Port diameter: Rp 1/2in.
Minimum flow (qi): 45l/h
Maximum flow (qs): 150l/h
Delta-P: 20...400kPa
V5004TY10150600
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 2.9 mm
DN size: 15mm
Port connection: internal threads
Port diameter: Rp 1/2in.
Minimum flow (qi): 60l/h
Maximum flow (qs): 600l/h
Delta-P: 25...400kPa
V5004TY10150780
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 2.9 mm
DN size: 15mm
Port connection: internal threads
Port diameter: Rp 1/2in.
Minimum flow (qi): 78l/h
Maximum flow (qs): 780l/h
Delta-P: 35...400kPa
V5004TY10201000
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 2.9 mm
DN size: 20mm
Port connection: internal threads
Port diameter: Rp 3/4in.
Minimum flow (qi): 100l/h
Maximum flow (qs): 1000l/h
Delta-P: 30...400kPa
V5004TY10201500
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 2.9 mm
DN size: 20mm
Port connection: internal threads
Port diameter: Rp 3/4in.
Minimum flow (qi): 450l/h
Maximum flow (qs): 1500l/h
Delta-P: 35...400kPa
V5004TY10202200
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 6.0 mm
DN size: 20mm
Port connection: internal threads
Port diameter: Rc 3/4in.
Minimum flow (qi): 220l/h
Maximum flow (qs): 2200l/h
Delta-P: 25...400kPa
V5004TY10202700
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 6.0 mm
DN size: 20mm
Port connection: internal threads
Port diameter: Rc 3/4in.
Minimum flow (qi): 270l/h
Maximum flow (qs): 2700l/h
Delta-P: 25...400kPa
V5004TY10251500
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 2.9 mm
DN size: 25mm
Port connection: internal threads
Port diameter: Rp 1in.
Minimum flow (qi): 450l/h
Maximum flow (qs): 1500l/h
Delta-P: 35...400kPa
V5004TY10252200
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 6.0 mm
DN size: 25mm
Port connection: internal threads
Port diameter: Rc 1in.
Minimum flow (qi): 220l/h
Maximum flow (qs): 2200l/h
Delta-P: 25...400kPa
V5004TY10252700
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 6.0 mm
DN size: 25mm
Port connection: internal threads
Port diameter: Rc 1in.
Minimum flow (qi): 270l/h
Maximum flow (qs): 2700l/h
Delta-P: 25...400kPa
V5004TY10322700
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 6.0 mm
DN size: 32mm
Port connection: internal threads
Port diameter: Rc 11/4in.
Minimum flow (qi): 270l/h
Maximum flow (qs): 2700l/h
Delta-P: 25...400kPa
V5004TY10323000
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Valve stroke 6.0 mm
DN size: 32mm
Port connection: internal threads
Port diameter: Rc 11/4in.
Minimum flow (qi): 300l/h
Maximum flow (qs): 3000l/h
Delta-P: 35...400kPa
V5004TY10326000
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve (90)
DN size: 32mm
Port connection: internal threads
Port diameter: Rc 11/4in.
Minimum flow (qi): 1800l/h
Maximum flow (qs): 6000l/h
Delta-P: 30...400kPa
V5004TY10409000
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve (90)
DN size: 40mm
Port connection: internal threads
Port diameter: Rc 11/2in.
Minimum flow (qi): 2700l/h
Maximum flow (qs): 9000l/h
Delta-P: 35...400kPa
V5004TY10501200
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve (90)
DN size: 50mm
Port connection: internal threads
Port diameter: Rc 2in.
Minimum flow (qi): 3300l/h
Maximum flow (qs): 11000l/h
Delta-P: 40...400kPa
V5004TY10501700
Trend V5004T Kombi-QM Pressure Independent Balancing and Control Valve
The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN150
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html
Rotary valve (90)
DN size: 50mm
Port connection: internal threads
Port diameter: Rc 2in.
Minimum flow (qi): 5400l/h
Maximum flow (qs): 18000l/h
Delta-P: 35...400kPa
V5011E1165
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 15mm
Connection diameter: G1 1/8in.
Kvs value: 0.63
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011E1171
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 15mm
Connection diameter: G1 1/8in.
Kvs value: 1
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011E1189
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 15mm
Connection diameter: G1 1/8in.
Kvs value: 1.6
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011E1197
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 15mm
Connection diameter: G1 1/8in.
Kvs value: 2.5
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011E1205
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 15mm
Connection diameter: G1 1/8in.
Kvs value: 4
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011E1213
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 20mm
Connection diameter: G1 1/4in.
Kvs value: 6.3
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011E1221
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 25mm
Connection diameter: G1 1/2in.
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
V5011E1229
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 32mm
Connection diameter: G2in.
Kvs value: 16
Close off pressure with 600N motor: 700kPa
Close off pressure with 1800N motor: 1600kPa
V5011E1237
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 40mm
Connection diameter: G2 1/4in.
Kvs value: 25
Close off pressure with 600N motor: 460kPa
Close off pressure with 1800N motor: 1500kPa
V5011E1245
Trend Two-way control valve PN16, external threaded connections DN15-50, V5011E
For heating, ventilating and air conditioning, domestic hot water, open circuits; hot/cold water quality VDI2035.
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
Medium type: water
20 mm
DN size: 50mm
Connection diameter: G2 3/4in.
Kvs value: 40
Close off pressure with 600N motor: 260kPa
Close off pressure with 1800N motor: 850kPa
V5011R1000
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 15mm
Kvs value: 0.63
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011R1018
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 15mm
Kvs value: 1
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011R1026
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 15mm
Kvs value: 1.6
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011R1034
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011R1042
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011R1059
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011R1067
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
V5011R1075
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 700kPa
Close off pressure with 1800N motor: 1600kPa
V5011R1083
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 460kPa
Close off pressure with 1800N motor: 1500kPa
V5011R1091
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug brass
Medium type: water
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 260kPa
Close off pressure with 1800N motor: 850kPa
V5011S1005
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 15mm
Kvs value: 0.63
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011S1013
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 15mm
Kvs value: 1
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011S1021
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 15mm
Kvs value: 1.6
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011S1039
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011S1047
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011S1054
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5011S1062
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
V5011S1070
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 700kPa
Close off pressure with 1800N motor: 1600kPa
V5011S1088
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 460kPa
Close off pressure with 1800N motor: 1500kPa
V5011S1096
Trend Two-way control valve PN16, threaded connections DN15-50, V5011R,S
For heating, ventilating and air conditioning; hot/cold water quality VDI2035.
Valve series: V5011R/S
Valve type: 2-way
Materials: body brass, stem stainless steel; plug brass or stainless steel
Action to open: stem up
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm, plug stainless steel
Medium type: steam (water)
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 260kPa
Close off pressure with 1800N motor: 850kPa
V5013E1063
Trend Three-way control valve PN16, flat sealing DN15-50, V5013E
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013E
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
20 mm
DN size: 15mm
Connection diameter: G1 1/8in.
Kvs value: 2.5
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5013E1071
Trend Three-way control valve PN16, flat sealing DN15-50, V5013E
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013E
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
20 mm
DN size: 15mm
Connection diameter: G1 1/8in.
Kvs value: 4
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5013E1089
Trend Three-way control valve PN16, flat sealing DN15-50, V5013E
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013E
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
20 mm
DN size: 20mm
Connection diameter: G1 1/4in.
Kvs value: 6.3
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5013E1097
Trend Three-way control valve PN16, flat sealing DN15-50, V5013E
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013E
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
20 mm
DN size: 25mm
Connection diameter: G1 1/2in.
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
V5013E1105
Trend Three-way control valve PN16, flat sealing DN15-50, V5013E
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013E
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
20 mm
DN size: 32mm
Connection diameter: G2in.
Kvs value: 16
Close off pressure with 600N motor: 700kPa
Close off pressure with 1800N motor: 1600kPa
V5013E1113
Trend Three-way control valve PN16, flat sealing DN15-50, V5013E
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013E
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
20 mm
DN size: 40mm
Connection diameter: G2 1/4in.
Kvs value: 25
Close off pressure with 600N motor: 460kPa
Close off pressure with 1800N motor: 1500kPa
V5013E1121
Trend Three-way control valve PN16, flat sealing DN15-50, V5013E
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013E
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: mod.equal%
20 mm
DN size: 50mm
Connection diameter: G2 3/4in.
Kvs value: 40
Close off pressure with 600N motor: 260kPa
Close off pressure with 1800N motor: 850kPa
V5013R1032
Trend Three-way control valve PN16, threaded connections DN15-50, V5013R
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013R
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5013R1040
Trend Three-way control valve PN16, threaded connections DN15-50, V5013R
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013R
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5013R1057
Trend Three-way control valve PN16, threaded connections DN15-50, V5013R
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013R
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
V5013R1065
Trend Three-way control valve PN16, threaded connections DN15-50, V5013R
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013R
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
V5013R1073
Trend Three-way control valve PN16, threaded connections DN15-50, V5013R
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013R
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 700kPa
Close off pressure with 1800N motor: 1600kPa
V5013R1081
Trend Three-way control valve PN16, threaded connections DN15-50, V5013R
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013R
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 460kPa
Close off pressure with 1800N motor: 1500kPa
V5013R1099
Trend Three-way control valve PN16, threaded connections DN15-50, V5013R
For heating, ventilating and air conditioning, open circuits; hot/cold water quality VDI2035.
Valve series: V5013R
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 20mm
Media temp.: 2...170C
Pressure rating: PN16
Port connection: internal threads ISO228
Flow char.: mod.equal%
20 mm
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 260kPa
Close off pressure with 1800N motor: 850kPa
V5025A1019
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 0.4
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1027
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 0.63
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1035
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 1
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1043
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 1.6
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1050
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1068
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1076
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1084
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1092
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1100
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1118
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1126
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 65mm
Kvs value: 63
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1134
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 80mm
Kvs value: 100
Close off pressure with 600N motor: 2500kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
V5025A1142
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
38 mm
DN size: 100mm
Kvs value: 160
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 2500kPa
Stroke: 38mm
V5025A1159
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
38 mm
DN size: 125mm
Kvs value: 250
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 2500kPa
Stroke: 38mm
V5025A1167
Trend Two-way control valve PN25, high differential pressure DN15-150, V5025A
Pressure balanced control valve for closed circuit systems.
For district heating; hot or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5025A
Valve type: 2-way press. bal.
Medium type: water
Materials: body nodular iron GGG40.3, trim stainless steel
Action to open: stem up
Media temp.: 2...200C
Pressure rating: PN25
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..80 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
38 mm
DN size: 150mm
Kvs value: 360
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 2500kPa
Stroke: 38mm
V5050A1090
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
38 mm, mixing
Valve type: 3-way mixing
DN size: 100mm
Kvs value: 160
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 230kPa
Stroke: 38mm
Media temp.: 2...220C
Flow char.: linear
V5050A1108
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
38 mm, mixing
Valve type: 3-way mixing
DN size: 125mm
Kvs value: 250
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 90kPa
Stroke: 38mm
Media temp.: 2...220C
Flow char.: linear
V5050A1116
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
38 mm, mixing
Valve type: 3-way mixing
DN size: 150mm
Kvs value: 360
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 90kPa
Stroke: 38mm
Media temp.: 2...220C
Flow char.: linear
V5050A1124
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 2500kPa
Stroke: 20mm
V5050A1132
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 2500kPa
Stroke: 20mm
V5050A1140
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 2500kPa
Stroke: 20mm
V5050A1157
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 2500kPa
Stroke: 20mm
V5050A1165
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 600kPa
Close off pressure with 1800N motor: 2000kPa
Stroke: 20mm
V5050A1173
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 350kPa
Close off pressure with 1800N motor: 1300kPa
Stroke: 20mm
V5050A1181
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 200kPa
Close off pressure with 1800N motor: 750kPa
Stroke: 20mm
V5050A1199
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 65mm
Kvs value: 63
Close off pressure with 600N motor: 120kPa
Close off pressure with 1800N motor: 500kPa
Stroke: 20mm
V5050A1207
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
20 mm
Valve type: 3-way mixing
DN size: 80mm
Kvs value: 100
Close off pressure with 600N motor: 50kPa
Close off pressure with 1800N motor: 230kPa
Stroke: 20mm
V5050A1215
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
38 mm, mixing
Valve type: 3-way mixing
DN size: 100mm
Kvs value: 160
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 230kPa
Stroke: 38mm
V5050B1064
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
38 mm, diverting, action to open AB-A: stem up
Valve type: 3-way diverting
DN size: 100mm
Kvs value: 160
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 230kPa
Stroke: 38mm
Media temp.: 2...220C
Flow char.: linear
V5050B1072
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
38 mm, diverting, action to open AB-A: stem up
Valve type: 3-way diverting
DN size: 125mm
Kvs value: 250
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 90kPa
Stroke: 38mm
Media temp.: 2...220C
Flow char.: linear
V5050B1080
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
38 mm, diverting, action to open AB-A: stem up
Valve type: 3-way diverting
DN size: 150mm
Kvs value: 360
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 90kPa
Stroke: 38mm
Media temp.: 2...220C
Flow char.: linear
V5050B1155
Trend Three-way control valve PN25/40, flanged connections DN15-100, V5050A,B
For closed circuit heating systems, hot water quality VDI2035.
Valve series: V5050
Medium type: water
Materials: body cast steel GS-C25, trim stainless steel
Action to open: stem down
Media temp.: 2...220C
Pressure rating: PN25/40
Port connection: flanges ISO7005
Flow char.: linear
38 mm, diverting, action to open AB-A: stem up
Valve type: 3-way diverting
DN size: 100mm
Kvs value: 160
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 230kPa
Stroke: 38mm
V5328A1005
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 1
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
V5328A1013
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 1.6
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
V5328A1021
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1039
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1047
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 20mm
Kvs value: 4
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1054
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1062
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: 1600kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1070
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 600kPa
Close off pressure with 1800N motor: 1600kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1088
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 350kPa
Close off pressure with 1800N motor: 1300kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1096
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 200kPa
Close off pressure with 1800N motor: 750kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1104
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 65mm
Kvs value: 63
Close off pressure with 600N motor: 120kPa
Close off pressure with 1800N motor: 470kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1112
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 80mm
Kvs value: 100
Close off pressure with 600N motor: 50kPa
Close off pressure with 1800N motor: 230kPa
Stroke: 20mm
Media temp.: 2...170C
V5328A1138
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 0.25
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
V5328A1146
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 0.4
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
V5328A1153
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
20 mm
DN size: 15mm
Kvs value: 0.63
Close off pressure with 600N motor: 1600kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
V5328A1195
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
38 mm
DN size: 100mm
Kvs value: 160
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 230kPa
Stroke: 38mm
Media temp.: 2...200C
V5328A1203
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
38 mm
DN size: 125mm
Kvs value: 250
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 90kPa
Stroke: 38mm
Media temp.: 2...200C
V5328A1211
Trend Two-way control valve PN16, flanged connections DN15-150, V5328A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035.
Valve series: V5328A
Valve type: 2-way
Medium type: steam (water)
Materials: body cast iron GG25, trim stainless steel
Action to open: stem up
Pressure rating: PN16
Port connection: flanges ISO7005
Flow char.: mod.equal%
Models DN15..50 approved according DIN EN 14597 (up to 130 oC), with motors ML6425A, ML7425A.
38 mm
DN size: 150mm
Kvs value: 360
Close off pressure with 600N motor: no
Close off pressure with 1800N motor: 90kPa
Stroke: 38mm
Media temp.: 2...200C
V5329A1004
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1012
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1020
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1038
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 1000kPa
Close off pressure with 1800N motor: no
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1046
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 790kPa
Close off pressure with 1800N motor: 1000kPa
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1053
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 480kPa
Close off pressure with 1800N motor: 1000kPa
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1061
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 260kPa
Close off pressure with 1800N motor: 1000kPa
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1079
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 65mm
Kvs value: 63
Close off pressure with 600N motor: 160kPa
Close off pressure with 1800N motor: 650kPa
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329A1087
Trend Three-way control valve PN16, flanged connections DN 15-150, V5329A/V5050A,B
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329A/V5050
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN16
Port connection: flanges ISO7005
20 mm
Valve type: 3-way mixing
DN size: 80mm
Kvs value: 100
Close off pressure with 600N motor: 100kPa
Close off pressure with 1800N motor: 400kPa
Stroke: 20mm
Media temp.: 2...170C
Flow char.: mod.equal%
V5329C1000
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 15mm
Kvs value: 2.5
Close off pressure with 600N motor: 600kPa
Close off pressure with 1800N motor: no
V5329C1018
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 15mm
Kvs value: 4
Close off pressure with 600N motor: 600kPa
Close off pressure with 1800N motor: no
V5329C1026
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 20mm
Kvs value: 6.3
Close off pressure with 600N motor: 600kPa
Close off pressure with 1800N motor: no
V5329C1034
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 25mm
Kvs value: 10
Close off pressure with 600N motor: 600kPa
Close off pressure with 1800N motor: no
V5329C1042
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 32mm
Kvs value: 16
Close off pressure with 600N motor: 600kPa
Close off pressure with 1800N motor: no
V5329C1059
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 40mm
Kvs value: 25
Close off pressure with 600N motor: 480kPa
Close off pressure with 1800N motor: 600kPa
V5329C1067
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 50mm
Kvs value: 40
Close off pressure with 600N motor: 260kPa
Close off pressure with 1800N motor: 600kPa
V5329C1075
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 65mm
Kvs value: 63
Close off pressure with 600N motor: 160kPa
Close off pressure with 1800N motor: 600kPa
V5329C1083
Trend Three-way control valve PN6, flanged connections DN15-150, V5329C/V5015A
For heating and air conditioning in closed circuit systems; hot/cold water quality VDI2035, greenhouses.
Valve series: V5329C/V5015
Valve type: 3-way mixing
Medium type: water
Materials: body cast iron GG25, trim stainless steel
Action to open: stem down
Pressure rating: PN6
Port connection: flanges ISO7005
Flow char.: mod.equal%
Stroke: 20mm
Media temp.: 2...170C
20 mm
DN size: 80mm
Kvs value: 100
Close off pressure with 600N motor: 100kPa
Close off pressure with 1800N motor: 400kPa
V5421B1009
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 25mm
Kvs value: 26
Max. delta P: 1600kPa
Torque for max. delta P: 8Nm
Media temp.: -10...120C
V5421B1017
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 32mm
Kvs value: 26
Max. delta P: 1600kPa
Torque for max. delta P: 8Nm
Media temp.: -10...120C
V5421B1025
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 40mm
Kvs value: 50
Max. delta P: 1600kPa
Torque for max. delta P: 12Nm
Media temp.: -10...120C
V5421B1033
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 50mm
Kvs value: 116
Max. delta P: 1000kPa
Torque for max. delta P: 12Nm
Media temp.: -10...120C
V5421B1041
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 65mm
Kvs value: 259
Max. delta P: 1000kPa
Torque for max. delta P: 15Nm
Media temp.: -10...120C
V5421B1058
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 80mm
Kvs value: 377
Max. delta P: 1000kPa
Torque for max. delta P: 25Nm
Media temp.: -10...120C
V5421B1066
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 100mm
Kvs value: 763
Max. delta P: 800kPa
Torque for max. delta P: 40Nm
Media temp.: -10...120C
V5421B1074
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 125mm
Kvs value: 1030
Max. delta P: 600kPa
Torque for max. delta P: 40Nm
Media temp.: 0...90C
V5421B1082
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 150mm
Kvs value: 1790
Max. delta P: 400kPa
Torque for max. delta P: 40Nm
Media temp.: 0...90C
V5421B1090
Trend Butterfly valve DN25..200
For heating applications, or boiler management systems.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5421B
Valve type: butterfly for motor
Medium type: water
Materials: rotary disc DN25-80 stainless steel 1.4581, DN100-200 ductile iron GGG40; coating DeltaMagni
Packing: EPDM
Angle of rotation: 90o
Pressure rating: PN16
Port connection: wafer
Without flanges. Actuators (M6061.., M7061.., M6422L1003) to be ordered seperatley.
DN size: 200mm
Kvs value: 3460
Max. delta P: 300kPa
Torque for max. delta P: 60Nm
Media temp.: 0...90C
V5422E1001
Trend Motorized Butterfly valve DN250..300
Butterfly valve with factory mounted electrical actuator.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5422L/E
Valve type: butterfly motorized
Medium type: water
Materials: body and disc ductile iron GGG40, disc coating DeltaMagni, shaft stainless steel 1.4021
Packing: EPDM
Protection class: IP67
Position indication: mechanical pointer
Max. delta P: 1000kPa
Angle of rotation: max. 90o
Pressure rating: PN10
Port connection: wafer
Manual operation: with wheel
Without flanges.
Power supply: 230Vac
Runtime: 30s
Media temp.: -10...120C
Modulating control and electrical position indication, Microswitch settings for signals values 0/2..10V, 0/4..20mA
DN size: 250mm
Kvs value: 5070
Torque: 250Nm
Control input signal: 0/2..10V=; 0/4..20mA
V5422E1019
Trend Motorized Butterfly valve DN250..300
Butterfly valve with factory mounted electrical actuator.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5422L/E
Valve type: butterfly motorized
Medium type: water
Materials: body and disc ductile iron GGG40, disc coating DeltaMagni, shaft stainless steel 1.4021
Packing: EPDM
Protection class: IP67
Position indication: mechanical pointer
Max. delta P: 1000kPa
Angle of rotation: max. 90o
Pressure rating: PN10
Port connection: wafer
Manual operation: with wheel
Without flanges.
Power supply: 230Vac
Runtime: 30s
Media temp.: -10...120C
Modulating control and electrical position indication, Microswitch settings for signals values 0/2..10V, 0/4..20mA
DN size: 300mm
Kvs value: 7430
Torque: 600Nm
Control input signal: 0/2..10V=; 0/4..20mA
V5422L1006
Trend Motorized Butterfly valve DN250..300
Butterfly valve with factory mounted electrical actuator.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5422L/E
Valve type: butterfly motorized
Medium type: water
Materials: body and disc ductile iron GGG40, disc coating DeltaMagni, shaft stainless steel 1.4021
Packing: EPDM
Protection class: IP67
Position indication: mechanical pointer
Max. delta P: 1000kPa
Angle of rotation: max. 90o
Pressure rating: PN10
Port connection: wafer
Manual operation: with wheel
Without flanges.
Power supply: 230Vac
Runtime: 30s
Media temp.: -10...120C
3-pt control, with 2x SPST 230 Vac end switches for open/close feedback
DN size: 250mm
Kvs value: 5070
Torque: 250Nm
Control input signal: 3-pt
V5422L1014
Trend Motorized Butterfly valve DN250..300
Butterfly valve with factory mounted electrical actuator.
For heating water containing up to 50% glycol. Other additives possible, but contact Honeywell for confirmation.
Valve series: V5422L/E
Valve type: butterfly motorized
Medium type: water
Materials: body and disc ductile iron GGG40, disc coating DeltaMagni, shaft stainless steel 1.4021
Packing: EPDM
Protection class: IP67
Position indication: mechanical pointer
Max. delta P: 1000kPa
Angle of rotation: max. 90o
Pressure rating: PN10
Port connection: wafer
Manual operation: with wheel
Without flanges.
Power supply: 230Vac
Runtime: 30s
Media temp.: -10...120C
3-pt control, with 2x SPST 230 Vac end switches for open/close feedback
DN size: 300mm
Kvs value: 7430
Torque: 600Nm
Control input signal: 3-pt
V5822A1006
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.16
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A1014
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.25
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A1022
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.4
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A1030
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.63
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A1048
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1
Close off pressure with 90N motor: 180kPa
Close off pressure with 180N motor: 1200kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A1055
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 180kPa
Close off pressure with 180N motor: 1200kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A1063
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 400kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A1071
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 4
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 400kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5822A4000
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
2,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 180kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5822A4018
Trend Two-way control valve PN16, conical sealing DN15/20, V5822A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5822A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types).
2,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5823A2003
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.25
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2011
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.4
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2029
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.63
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2037
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: 250kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2045
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: 250kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2052
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 100kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2060
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 4
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 100kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2151
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: no
Close off pressure with 180N motor: 240kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A2169
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 4
Close off pressure with 90N motor: no
Close off pressure with 180N motor: 240kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823A4009
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
2,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5823A4017
Trend Three-way control valve PN16, conical sealing DN15/20, V5823A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
2,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5823C2009
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.25
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2017
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.4
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2025
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.63
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2033
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: 250kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2041
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: 250kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2058
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 100kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2066
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 4
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 100kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2157
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: no
Close off pressure with 180N motor: 240kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C2165
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 4
Close off pressure with 90N motor: no
Close off pressure with 180N motor: 240kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5823C4005
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
2,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5823C4013
Trend Three-way/bypass control valve PN16, conical sealing DN15/20, V5823C
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5823C
Valve type: 3-way mixing, bypass
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread con. sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
2,5 mm
DN size: 20mm
Connection diameter: 1 1/8" x 14in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5832A1004
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.16
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A1012
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.25
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A1020
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.4
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A1038
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.63
Close off pressure with 90N motor: 600kPa
Close off pressure with 180N motor: 1600kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A1046
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1
Close off pressure with 90N motor: 180kPa
Close off pressure with 180N motor: 1200kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A1053
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 180kPa
Close off pressure with 180N motor: 1200kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A1061
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 20mm
Connection diameter: G3/4in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 400kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A1079
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
6,5 mm
DN size: 20mm
Connection diameter: G3/4in.
Kvs value: 4
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 400kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5832A4008
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
2,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 180kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5832A4016
Trend Two-way control valve PN16, flat sealing DN15/20, V5832A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832A
Valve type: 2-way
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem up
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types).
2,5 mm
DN size: 20mm
Connection diameter: G3/4in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: no
Stroke: 2.5mm
Flow char.: on/off
V5832B2075
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Pressure balanced control valve.
For fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832B2
Valve type: 2-way press. bal.
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 6.5mm
Media temp.: 2...130C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: linear
Valves are supplied with adjustment cap.
6,5 mm
DN size: 25mm
Connection diameter: G1 1/2in.
Kvs value: 4
Close off pressure with 300N motor: 1600kPa
Close off pressure with 400N motor: 1600kPa
V5832B2083
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Pressure balanced control valve.
For fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832B2
Valve type: 2-way press. bal.
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 6.5mm
Media temp.: 2...130C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: linear
Valves are supplied with adjustment cap.
6,5 mm
DN size: 25mm
Connection diameter: G1 1/2in.
Kvs value: 6.3
Close off pressure with 300N motor: 1600kPa
Close off pressure with 400N motor: 1600kPa
V5832B2091
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Pressure balanced control valve.
For fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832B2
Valve type: 2-way press. bal.
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 6.5mm
Media temp.: 2...130C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: linear
Valves are supplied with adjustment cap.
6,5 mm
DN size: 25mm
Connection diameter: G1 1/2in.
Kvs value: 10
Close off pressure with 300N motor: 1600kPa
Close off pressure with 400N motor: 1600kPa
V5832B2109
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Pressure balanced control valve.
For fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832B2
Valve type: 2-way press. bal.
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 6.5mm
Media temp.: 2...130C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: linear
Valves are supplied with adjustment cap.
6,5 mm
DN size: 32mm
Connection diameter: G2in.
Kvs value: 16
Close off pressure with 300N motor: 1200kPa
Close off pressure with 400N motor: 1200kPa
V5832B2117
Trend Two-way control valve PN16, flat sealing DN25-40, V5832B
Pressure balanced control valve.
For fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5832B2
Valve type: 2-way press. bal.
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 6.5mm
Media temp.: 2...130C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: linear
Valves are supplied with adjustment cap.
6,5 mm
DN size: 40mm
Connection diameter: G2 1/4in.
Kvs value: 25
Close off pressure with 300N motor: 1000kPa
Close off pressure with 400N motor: 1000kPa
V5833A1003
Trend Three-way control valve PN16, flat sealing DN15/20, V5833A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.25
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5833A1011
Trend Three-way control valve PN16, flat sealing DN15/20, V5833A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.4
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5833A1029
Trend Three-way control valve PN16, flat sealing DN15/20, V5833A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 0.63
Close off pressure with 90N motor: 500kPa
Close off pressure with 180N motor: 800kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5833A1037
Trend Three-way control valve PN16, flat sealing DN15/20, V5833A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: 250kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5833A1045
Trend Three-way control valve PN16, flat sealing DN15/20, V5833A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 15mm
Connection diameter: G1/2in.
Kvs value: 1.6
Close off pressure with 90N motor: 150kPa
Close off pressure with 180N motor: 250kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5833A1052
Trend Three-way control valve PN16, flat sealing DN15/20, V5833A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: G3/4in.
Kvs value: 2.5
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 100kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5833A1060
Trend Three-way control valve PN16, flat sealing DN15/20, V5833A
For individual room control, fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A
Valve type: 3-way mixing
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Media temp.: 2...120C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Valves are supplied with adjustment cap (not for on/off types). If the main-port (A-AB) is equal percentage, the B-AB port is linear. The valve capacity of B-AB is one stage smaller.
6,5 mm
DN size: 20mm
Connection diameter: G3/4in.
Kvs value: 4
Close off pressure with 90N motor: 50kPa
Close off pressure with 180N motor: 100kPa
Stroke: 6.5mm
Flow char.: mod.equal%
V5833A2076
Trend Three-way control valve PN16, flat sealing DN25-40, V5833A
Pressure balanced control valve.
For fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A2
Valve type: 3-way mixing, press. bal.
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 6.5mm
Media temp.: 2...130C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: linear
Valves are supplied with adjustment cap.
6,5 mm
DN size: 25mm
Connection diameter: G1 1/2in.
Kvs value: 4
Close off pressure with 300N motor: 600kPa
Close off pressure with 400N motor: 1600kPa
V5833A2084
Trend Three-way control valve PN16, flat sealing DN25-40, V5833A
Pressure balanced control valve.
For fan coil units and small re-heaters/re-coolers; hot water or cold water (max. 50% glycol), water quality VDI2035.
Valve series: V5833A2
Valve type: 3-way mixing, press. bal.
Medium type: water
Materials: body brass, stem stainless steel, plug brass
Action to open: stem down
Stroke: 6.5mm
Media temp.: 2...130C
Pressure rating: PN16
Port connection: ext. thread flat sealing
Flow char.: linear
Valves are supplied with adjustment c